To start the tool, slide the switch lever to the "I" position. To stop the tool, slide the switch lever to the "O" position.

Speed adjusting dial

For 4351CT, 4351FCT

1

1. Speed adjusting

dial

 

 

 

008032

The tool speed can be infinitely adjusted between 800 and 2,800 strokes per minute by turning the adjusting dial. Higher speed is obtained when the dial is turned in the direction of number 5; lower speed is obtained when it is turned in the direction of number 1.

Refer to the table to select the proper speed for the workpiece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced.

Workpiece to be cut

Number on adjusting dial

Wood

4 - 5

Mild steel

3 - 5

Stainless steel

3 - 4

Aluminum

3 - 5

Plastics

1 - 4

006368

CAUTION:

•The speed adjusting dial can be turned only as far

as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work.

The tools equipped with electronic function are easy to operate because of the following features.

Constant speed control

Electronic speed control for obtaining constant speed. Possible to get fine finish, because the rotating speed is kept constant even under load condition.

Soft start feature

Safety and soft start because of suppressed starting shock.

Lighting up the lamps

For 4351FCT only

CAUTION:

•Do not look in the light or see the source of light

directly.

To turn on the lamp, pull the trigger. Release the trigger to turn it off.

NOTE:

•Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination.

ASSEMBLY

CAUTION:

•Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

Installing or removing saw blade

CAUTION:

•Always clean out all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may cause insufficient tightening of the blade, resulting in a serious personal injury.

•Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin.

•Tighten the saw blade securely. Failure to do so may cause a serious injury.

•When you remove the saw blade, be careful not to hurt your fingers with the top of the blade or the tips of workpiece.

To install the blade, open the tool opener to the position shown in the figure.

1. Tool opener

1

008007

Keeping that situation, insert the saw blade into the blade clamp as far as the two protrusions of the blade can not be seen.

3

1. Blade clamp

2. Jig saw blade

 

 

3. Protrusions

1

 

2

 

008008

 

Return the tool opener to its original position.

After installing, always make sure that the blade is securely held in place by trying to pull it out.

5

Page 4 Page 6
Page 5
Image 5
Makita 4351T, 4351FCT, 4351CT Assembly, Speed adjusting dial, Lighting up the lamps, Installing or removing saw blade
Page 4 Page 6

4351CT, 4351T, 4351FCT specifications

The Makita 4351FCT, 4351T, and 4351CT are powerful and efficient tools designed for professional woodworkers and DIY enthusiasts alike. Each model features an array of advanced technologies and robust characteristics that set them apart in the market.

One of the standout features of these jigsaws is the variable speed control that allows users to adjust the speed of the blade between 800 and 2,800 strokes per minute. This flexibility makes it easy to tailor the speed to suit different materials and types of cuts. The saws are equipped with a powerful 720W motor, providing sufficient power for cutting through various materials, including wood, plastic, and metal.

The 4351 series incorporates a patented tool-less blade change system, which simplifies the process of swapping out blades. This feature enhances productivity by allowing users to change blades quickly without the need for additional tools. The saws also support a wide variety of blade types, granting excellent versatility while tackling different projects.

Another remarkable characteristic is the built-in LED light that illuminates the cutting line, ensuring accuracy even in poorly lit work environments. Additionally, the dust blower function keeps the cutting line clear from debris, providing better visibility and cleaner cuts.

In terms of design, the Makita 4351FCT, 4351T, and 4351CT all feature an ergonomic grip that enhances comfort during prolonged use. The saw's rubberized grip reduces vibrations, minimizing fatigue and enabling more precise control. The adjustable base plate allows for bevel cuts of up to 45 degrees, giving users the ability to execute intricate designs effortlessly.

All models in the 4351 series come with a 3-year limited warranty, reflecting Makita's commitment to quality and durability. They are designed to withstand the rigors of daily use, making them a reliable choice for professionals in construction, carpentry, and renovation.

When it comes to performance, the Makita 4351FCT, 4351T, and 4351CT lead the pack with their exceptional cutting speed, precision, and ease of use. Whether you are a seasoned professional or a hobbyist, these jigsaws are perfect for achieving outstanding results in any woodworking project.
Top Page Image Contents