|
|
|
|
|
| EN 73 | |
|
|
|
|
|
|
| |
| RECORDING |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
|
| 1. | Recording will not start, and |
| ● There is no cassette loaded. |
| Insert a cassette. |
|
|
| “CASS” blinks on the front display |
| ● The loaded cassette has had its |
| Remove the cassette and cover the |
|
|
| panel for about 5 seconds. |
| record safety tab removed. |
| hole with adhesive tape, or load a |
|
|
|
|
|
|
| cassette on which the record safety |
|
|
|
|
|
|
| tab is intact. |
|
|
|
|
|
|
|
|
|
| 2. | TV broadcasts will not be recorded |
| ● The VCR has been set to |
| Select the appropriate channel on the |
|
|
| properly. |
|
| VCR. |
| |
|
|
|
| location by mistake. |
|
|
|
|
|
|
|
|
|
|
|
| 3. |
| ● The components have been |
| Connect the components correctly |
| |
|
|
|
| incorrectly connected, or correct |
| ( pg. 64, 66) or check “REAR AUX |
|
|
|
|
| video connector (S VIDEO, VIDEO |
|
| |
|
|
|
| or DV) is not selected. |
| setting ( pg. 56). |
|
|
|
|
| ● The power to one or more of the |
| Make sure the power to all units is on. |
|
|
|
|
| units has not been turned on. |
|
|
|
|
|
|
| ● The recording VCR’s input location |
| Select the appropriate input location |
|
|
|
|
| has been set incorrectly. |
| on the recording VCR. |
|
|
|
|
|
|
|
| |
| TIMER RECORDING |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
|
| 1. | Timer recording will not work. |
| ● The clock and/or the timer have |
| Set the clock and/or timer correctly. |
|
|
|
|
| been set incorrectly. |
|
|
|
|
|
|
| ● The timer is not engaged. |
| Press TIMER (‰) and check to make |
|
|
|
|
|
|
| sure that ‰ appears on the front |
|
|
|
|
|
|
| display panel. |
|
|
|
|
| ● The VCR has not been set up properly. |
|
| |
|
|
|
|
|
| Make sure you have compensated for |
|
|
|
|
|
|
| guide channel and VCR or cable box |
|
|
|
|
|
|
| channel number mismatches |
|
|
|
|
|
|
| ( pg. 36). |
|
|
|
|
|
|
|
|
|
| 2. | Timer programing will not work. |
| ● Timer recording is in progress. |
| Timer programing cannot be performed |
|
|
|
|
|
|
| when timer recording is in progress. |
|
|
|
|
|
|
| Wait until it finishes. |
|
|
|
|
|
|
|
|
|
| 3. | “CASS” blinks on the front display |
| ● The timer is engaged but there is no |
| Load a cassette with the record safety |
|
|
| panel. |
| cassette loaded. |
| tab intact, or with the hole covered |
|
|
|
|
|
|
| with adhesive tape. |
|
|
|
|
|
|
|
| |
| 4. The cassette stops automatically, |
| ● The loaded cassette has had its |
| Remove the cassette and cover its |
| |
|
| and ‰, Q and $ on the front |
| record safety tab removed. |
| hole with adhesive tape, or replace it |
|
|
| display panel will not stop |
|
|
| with a cassette on which the safety |
|
|
| blinking. |
|
|
| tab is intact. |
|
|
|
|
| ● The tape reaches its end during |
| The program may not have been |
|
|
|
|
| timer recording. |
| recorded in its entirety. Next time be |
|
|
|
|
|
|
| sure you have enough time on the |
|
|
|
|
|
|
| tape to record the entire broadcast. |
|
|
|
|
|
|
|
|
|
| 5. | ‰ blinks for 10 seconds and the |
| ● TIMER (‰) has been pressed when |
| Check the programed data and set |
|
|
| timer mode is disengaged. |
| there are no programs in memory, or |
| again if necessary, then press TIMER |
|
|
|
|
| the timer recording program has not |
| (‰) again. |
|
|
|
|
| been set correctly. |
|
|
|
|
|
|
|
|
|
| |
| 6. Cable channels are not automatically |
| ● The Controller is not properly |
| Connect the Controller correctly |
| |
|
| switched during timer recording. |
| connected to the VCR. |
| ( pg. 15). |
|
|
|
|
| ● The input channel selected on the |
| After confirming your cable box’s |
|
|
|
|
| Cable Set Up screen is incorrect. |
| input channel number, |
|
|
|
|
|
|
| Cable Set Up screen and select the |
|
|
|
|
|
|
| correct number ( pg. 16). |
|
|
|
|
| ● The cable box is turned off. |
| Make sure the power is on before |
|
|
|
|
|
|
| timer recording starts. |
|
|
|
|
|
|
|
|
|
CONTINUED ON NEXT PAGE \