Operation, English, Connecting The Power Supply, W, e r

OPERATION

*In this instruction manual, some operations can only be performed with the remote control. For operations that can be performed with buttons both on the main unit and on the remote control, the

button names are shown in the mark. And for operations that can only be performed with

buttons on the remote control, the button names are shown in the mark.

To start playback form the first track

Press

PLAY button.

To stop playback

Press STOP button.

To eject disc

Press OPEN/CLOSE button to open the disc tray and take the disc off. Press the button again to close the tray.

7Switching Sound Mode (Super Audio CD)

SUPER AUDIO CD PLAYER SA8001

SOUND MODE Button

ENGLISH

CONNECTING THE POWER SUPPLY

qPress POWER switch to turn on.

Disc tray must be closed when the unit is not be used.

1Plug the power cable into AC IN jack on the back panel.

2Turn on the power switch of the audio unit (amplifier, etc.) that is connected with this unit. Set the selector on the connected unit to this unit.

3Plug the power cable into an AC outlet.

NORMAL PLAYBACK

7Super Audio CD player playback

SUPER AUDIO CD PLAYER SA8001

w, e r

Display

The display cycles from TOC Reading → No Disc (when no disc is loaded) → Super Audio CD (when the start sound mode setting is Super Audio CD).

wPress the OPEN/CLOSE button

The disc tray comes out. Place the disc with label side up on the tray.

To play a single (8cm) CD, place the disc with the indentation at the center of the tray.

ePress OPEN/CLOSE button.

rPress PLAY button.

Disc type is automatically detected and playback is started. Track number and track elapsed time(minute, second) appear on the display.

*For Super Audio CD/CD hybrid-layer discs (See page 2), the layer that is set in the start sound mode (See page 10) is played. To change the layer, use the SOUND MODE button. (See page 9)

(Exp.:Track 6, Elapsed time 2 min 8 sec)

Number of current track										Minutes				Seconds
			RNDM TRK				A – B						AMS
			RNDM TRK				A – B						AMS
			PROG				ALL		1			TOTAL SING REMAIN			SACD
TEXT	1	2	3	4	5	6	7	8	9 10	11 12	13 14	15 16	17 18	19 20	STEREO

Remaining track numbers

Playback automatically stops at the end of the final track.

To pause playback

Press PAUSE button.

PAUSE indicator will light and playback is paused at the point that the button is pressed. To restart

playback, press PAUSE button again or press PLAY button.

To change time display

Press the TIME button on the remote control. Each time TIME button is pressed, display will change in the following order. “Track elapsed time”

→“Track remaining time” → “Total remaining time”

→“Track elapsed time”.

•Track remaining time

(The remaining playing time from the playing point to the end of the current track)

“SING REMAIN” is displayed “–” is displayed

			RNDM TRK				A – B						AMS
			PROG				ALL		1			TOTAL	SING REMAIN		SACD
TEXT	1	2	3	4	5	6	7	8	9 10	11 12	13 14	15 16	17 18	19 20	STEREO

•Total remaining time

(The remaining playing time from the playing point to the end of the last track)

“–” is displayed												“TOTAL REMAIN”
“–” is displayed												is displayed
			RNDM TRK				A – B						AMS
			RNDM TRK				A – B						AMS
			PROG				ALL		1			TOTAL SING REMAIN			SACD
TEXT	1	2	3	4	5	6	7	8	9 10	11 12	13 14	15 16	17 18	19 20	STEREO

*If TIME button is pressed when Super Audio CD disc that supports text is in use, time display is given priority and the text information will not be displayed until the next track.To see the text information, press TEXT button.

qPress SOUND MODE button in stop

mode (not playing).

The currently selected layer or area is shown on the display. (CD or Super Audio CD)

If SOUND MODE button is pressed again, a playable layer or area will be shown, and the layer or area will be switched to new one.

*When layer or area is switched, TOC will be read again.

*The sound mode cannot be changed for Audio CDs and discs with only a Super Audio CD area.

*The sound mode on hybrid layer discs will be

changed in the following order.

Super Audio CD stereo area → CD layer → Super Audio CD stereo area

*Sound mode can be selected while the tray is open. Select a desired layer or area and press

PLAY button then the tray will close and playback will be started.

wPress the SOUND MODE button

during playback.