OTHER FUNCTION

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV-VIDEO in jack to control the power (ON/ OFF) to the SR5500.

AUTO POWER ON

1. Be sure the TV auto mode is ENABLED. (Refer page 19 : System Setup)

2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input.

3. Turn OFF the power to the TV TUNER and the SR5500.

4. Turn ON the TV TUNER and tune in a receivable station.

5. When the station is received, the SR5500 turns ON and TV is selected automatically.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER

ATTENUATION TO ANALOG INPUT

SIGNAL

T-MODE RDS F.DIRECT

INPUT/DISC+ AUDIO SUB-T/ATTPTY

CH.SEL

LIP.SYNC

SYSTEM REMOTE CONTROLLER

RC5500SR

If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the remote.

“ATT” indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD- OUT, VCR1-OUT and DSS/VCR2-OUT.

This function is memorized for each individual input source.

DOLBY HEADPHONE MODE

This feature simulates the waveforms of the actual sounds heard from the speakers.

When headphones are used, the MENU button automatically switches to the Dolby headphone mode.

The OSD that appears when the MENU button is pressed is shown below.

HEAD PHONE

DOLBY HP MODE

: BYPASS

SURROUND

: ✽✽✽

L LEVEL

: 0dB

R LEVEL

: 0dB

DOLDBY HP (Headphone) MODE can be selected with the left and right cursor buttons.

BYPASS → DH1 → DH2 → DH3 → BYPASS

BYPASS : Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo.

selecting the “VIDEO OFF” setting.

ENGLISH

VIDEO ON/OFF

 

When no video signal is connected to the SR5500

 

or a DVD, etc., is connected directly to your TV, the

 

unnecessary video circuit can be turned off by

 

To select video off, press the AMP button and

 

press the V-OFFbutton.

TUNER

CD

TAPE

CDR/MD

R5500

AUX1

AMP

 

TV

 

 

MAIN

VOL.

SLEEP

MUTE

VOL.

SURROUND

 

 

 

DIGITAL

 

 

 

AAC

 

 

 

OSD

 

MENU

NIGHT

CSII

EX/ES

VIRTUAL

 

4

5

6

DISPLAY

MCH-ST

STEREO

7.1CH IN

 

7

8

9

CLEAR

MEMO

A/D

P.SCAN/V-OFF

 

 

0

 

 

 

CHANNEL/SKIP

BASS

TREBLE

TUNE/SEARCH

DISPLAY MODE

 

SET UP/

MENU OFF

 

 

T.TONE

 

 

SR5500

PURE DIRECT

AUTO

2

DTS

 

 

1

3

 

NIGHT

CSII

EX/ES

VIRTUAL

OFF or select a channel that does not contain any broadcast.

2. The power to the SR5500 switches to STANDBY after approx. 5 minutes.

Notes:

•AUTO POWER OFF is canceled if the SR5500 is set to a source other than TV.

The function reactivates when TV is selected again.

•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.

•The S-Video terminal does not support “TV AUTO ON/OFF” function.

LISTENING THROUGH HEADPHONES

DH1 : The size of a typical living room space

This jack may be used to listen to the SR5500’s

is simulated.

 

output through a pair of headphones. Be certain

DH2 : The expansiveness of a structure as

that the headphones have a standard 1/4” stereo

large as a music hall is simulated.

phono plug . (Note that the speakers will

DH3 : A large space such as that found in a

automatically be turned off when the headphone

movie theater is simulated.

jack is in use.)

When the PURE DIRECT mode is selected, Dolby

 

AV SURROUND RECEIVER SR5500

surround processing is bypassed and “✽✽✽” is

 

displayed as the mode indication.

 

The surround mode can be selected when any of

 

the modes in DH1, DH2, or DH3 is selected.

 

L/R LEVEL can be set in the ±10 dB range.

 

SURROUND

4

5

6

 

DIGITAL

AAC

DISPLAY

MCH-ST

STEREO

7.1CH IN

 

 

7

8

9

 

CLEAR

MEMO

A/D

P.SCAN/V-OFF

 

 

 

0

 

 

 

 

CHANNEL/SKIP

 

BASS

TREBLE

TUNE/SEARCH

 

 

T-MODE

RDS

F.DIRECT

You can select the display mode for the front display of the SR5500.

To select this mode, press the DISPLAY on the remote control.

When this button is pressed, the display mode is switched in the following sequence.

→ Surround Mode → Auto-display Off → Display

Note:

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

Notes:

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

•TONE cannot be set when any of the modes in DH1, DH2, or DH3 is selected.

•The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input.

Off → Input Function → Surround Mode....

In Auto display off mode, the display is off. But, if

you make a change to the unit such as input or

surround mode, the display will show that change,

then go back to off after about 3 seconds. When

changing the volume, it is not displayed.

In Display off mode, the display is off completely.

Note:

•Only the DISP indicator will be illuminated on the front display in display off condition

27

SR5500U DFU_01_ENG 2_2

Page 27

04.8.2, 4:13 PM

Adobe PageMaker 6.5J/PPC