EL84 20/20 Front Panel Features
LEVEL | PRESENCE |
|
|
| OFF |
| OFF |
|
|
| |
|
|
|
|
|
|
|
| EL84 20/20 |
|
|
| STEREO VALVE POWER AMPLIFIER |
|
010 | 010 | ON | ON |
| DEEP STANDBY POWER | STANDBY | POWER |
ENGLISH
1 | 2 | 3 | 4 | 5 |
1.Level Controls Level or volume of the EL84 20/20.
2.Presence Adds brightness and top end bite to your sound.
3.Deep The Deep switch on the 20/20 affects the speaker damping. By depressing the Deep switch you will add more bottom end thud to your guitar sound. Similar to the difference between open and closed back cabinets.
4.Standby LED Indicates operating status of standby (see 6).
5.Power LED Indicates operating status of amp
(see 7).
6.Standby Controls the H.T. supply to the valves and allows the valves to remain heated when not in use.
67
7.Power On/Off Switch for mains power to the amplifier.
Note: To prolong the life of the valves it is always advisable to switch on the Mains Power Switch (item 7) about 1 minute before switching on the Standby (item 6). This allows the valves to heat up to full working temperature before use.
On switching off, the Standby should always be switched before the Power Switch.
The standby facility is particularly useful live, where before playing and between sets, it allows you to keep the valves operating at a slightly reduced temperature but without any sound being produced.
EL84 20/20 Rear Panel Features |
|
|
|
|
|
| |
MAINS INPUT |
|
|
|
|
|
|
|
| LEFT OUTPUTS |
| RIGHT OUTPUTS |
| REMOTE SWITCHING |
| INPUTS |
| 2x20 Watts RMS |
|
|
|
|
|
|
| POWER OUTPUT |
|
|
|
|
|
|
| INTO 8/16 Ω |
|
|
|
|
|
|
120V ~ 60Hz |
|
|
|
|
|
|
|
220 WATTS | 16Ω SPEAKER 8Ω | LINE | 16Ω SPEAKER 8Ω | LINE | DEEP | LEFT | RIGHT(MONO) |
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
1. Mains Input | Connects the amplifier to the mains |
| Note: When the 20/20 is in use, speakers must be | ||||||
power supply. |
|
|
| connected to both sides at all times. See Loading points |
Left Outputs
2.16 Ohm Jack Speaker jack for 16 Ohm speaker cabinet for left side of power amp.
3.8 Ohm Jack Speaker jack for 8 Ohm speaker cabinet for left side of power amp.
4.Line Attenuated version of speaker signal giving whole tone of power stage. For connection to subsequent effects processor and larger power amp.
Note: When 20/20 is in use, speakers must be connected to both sides at all times. See Loading points later.
Right Outputs
5.16 Ohm Jack Speaker jack for 16 Ohm speaker cabinet for right side of power amp.
6.8 Ohm Jack Speaker jack for 8 Ohm speaker cabinet for right side of power amp.
7.Line Attenuated version of speaker signal giving whole tone of power stage. For connection to subsequent effects processor and larger power amp.
Loading Points
Remote Switching
8.Deep In addition to the front panel, the Deep facility can be switched remotely by a footswitch or programmable device, such as an effects processor.
It should be noted that this will override the front panel switch position.
Inputs
9.Left Takes the left input from a stereo
10.Right (Mono) Takes the right input from a stereo
A mono input will drive both channels.
4