Marshall electronic MD-0514 specifications Product Overview, Features, Electrical Specifications

1Product Overview

The MD-0514is a multiformat 1 x 4 distribution amplifier, with signal bandwidth up to 350 MHz. This module can be used with VGA, SVGA, XGA, UXGA signals. An optional HD15 to 5 BNC cable (RGB- 5HD15-X) can be used for RGBHV, Y-Pr-Pb, YUV, RGB, and composite signals. Supports screen formats up to 0 x 1080

2Features

Signal Bandwidth up to 350Mhz Multiple applications

HD-15 Input Connection self terminating 75Ω 4 HD-15 Output Connections

All connections in rear of module Includes Power Supply Model V-PS6-1.2A

Install in wall with supplied brackets or use on the desktop

3Electrical Specifications

Signal Input	HD-15 (VGA, SVGA, XGA, UXGA, RGBHV, YUV, Composite)
Signal Output	4 HD-15
Frequency Response	10 to 350 MHz
K factor	<1%
Signal to Noise	>70 db
Dynamic gain/phase	<1% / <10
Cable length	250’
Power required	6 Volt D.C. supplied from V-PS6-1.2A (included) (1.2Amp Max)

4Mechanical Specifications

Dimensions	7.625”W x 4.125”D x 1.0”H
MD-0514 Weight	1.15 lbs (.52kg)
V-PS6-1.2A Power Supply Weight	0.20 lbs (0.10kg)

5Optional Accessories

	Cable: RGB-5HD15-X	V-CB1 Stand
	(X = Length in feet 6, 10, 15, 20)
2
		MD-0514 USERS GUIDE

6Operational Setup

1.Unpack the MD-0514, and accompanying V-PS6-1.2A power supply and physically inspect for any damage that may have occurred during shipping. Also verify there is a small package with mounting accessories. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606.

2.Install in your desired location. If wall mounting is required, attach the mounting brackets by removing the Phillips head screws on the sides, closest to the rear of the unit. (See below) Only one screw per side should be removed. Use the same screw to attach the bracket with the flange facing away from the side and parallel to the front of the MD-0514 metal case. The flange has two holes. For desktop use, apply the supplied rubber pads.

Determine your signal configuration from the table below:

INPUT SIGNAL	CABLE	OUTPUT SIGNAL	CABLE
VGA from Computer	HD-15 Male to Male	VGA to Projector	HD-15 Male to Male (Customer supplied)
	(Customer supplied)
VGA from Computer	HD-15 Male to Male	RGBHV to Projector or Monitor	RGB-5HD15-X (X=length)
	(Customer supplied)		(6,10, 15, 20 feet)
RGBHV	RGB-5HD15-X (X=length)	RGBHV to Projector or Monitor	RGB-5HD15-X (X=length)
	(6,10, 15, 20 feet)		(6,10, 15, 20 feet)
Y-Pr-Pb or RGB From camera	RGB-5HD15-X (X=length)	Y-Pr-Pb or RGB to monitor	RGB-5HD15-X (X=length)
	(6,10, 15, 20 feet)		(6,10, 15, 20 feet)
Composite Video group	RGB-5HD15-X (X=length)	Composite Video group	RGB-5HD15-X (X=length)
(RGB BNC) (3 Signals)	(6,10, 15, 20 feet)	(RGB BNC) (3 Signals)	(6,10, 15, 20 feet)

3. Connect required cables for signal input and output.

Note that 3 Composite video signals can be applied for distribution on the Red, Green, and Blue BNC connections of RGB-HD15-X breakout cable. (See Illustration next page)

4.Plug the power supply into the A.C. source

5.Attach power connection to the back of the unit to turn on power. Verify power on indicator active on the front of the MD-0514

Marshall Electronics 3