Marshall electronic V-R563P-SDI warranty Product Overview, Features, Operational Setup

1Product Overview

The V-R563P-SDIhas three independently controlled 5.6” active matrix LCD monitors. Each of the 5.6” panels produces high-resolution images with 960 x 234 pixels. The V-R563P-SDI also has a unique feature that allows the unit to tilt up or down for optimum viewing angle and installs into an EIA standard 19” rack. Each screen has one composite video with active loop through and one SDI (SMTPE 259M) input with active loop through, active clock recovery and automatic 75Ω termination. There is also a money saving Digital to Analog conversion of each SDI signal. Every display has a built-in color bar generator, 3 Tally indicators, individual front mounted selector buttons with LED indicators and color, tint, brightness and contrast controls. The unit includes a universal voltage power supply and features auto recognition for NTSC or PAL signals.

2Features

• Small Footprint – occupies only 3RU of a standard EIA 19 inch rack V-PS12-3.3A

• Ready to mount – all brackets are factory installed

• Lightweight - Save over 30 pounds when compared to similar CRT models

• All adjustments and selections are readily available. No menus!

• Easy to use front panel selection of inputs

• NTSC or Pal operation with automatic signal format detection

• Switched A/B Composite inputs with active loop out

• All inputs automatically terminate

• Built in color bar generator for each display

• Includes V-PS12-3.3A Universal power supply (U.L. class 2)

• Unique 180 degree tilt adjustment

• Dry erase label for each screen

5Operational Setup

1.Unpack the V-R563P-SDI and accompanying V-PS12-3.3A power supply. Physically inspect for any dam- age that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the continental united states call +1 310-333-0606.

2.After inspection, install in your desired location of a standard EIA 19-inch equipment rack. Adequate ventila- tion is required when installed to prevent possible damage to the V-R563P-SDI internal components.

3.Connect required cables for signal input and output.

Please note that power must be applied to the V-R563P-SDI for all outputs to be activated. All BNC connectors should be rated for 75Ω.

4.Plug the V-PS12-3.3A power supply into the A.C. source

5.Attach twist lock power connection from V-PS12-3.3A power supply to the back of the unit.

6.Turn on the V-R563P-SDI by depressing the power switch located on the front of the unit.

6Connectors

3Electrical Specifications

Display (Viewing Area)	5.6” diagonal (4.46” x 3.33”) (113.3 mm x 84.7mm)
Screen Aspect	4:3
Resolution (Dots)	960 pixel (320dot) W x 234H × 234V (225,000 pixels)
Dot Pitch	0.118mm(W) × 0.362mm (H)
Pixel Response Time	35ms typical
Brightness (in cd/m²)	300 cd/m²
Contrast Ratio	150:1
System	PAL or NTSC with automatic detection. NTSC signal complies to SMPTE RS-170M
Inputs per display	Composite BNC 75Ω self terminating 0.7V to 1.3 V P-P.
	SDI BNC 75Ω self terminating with 500ft equalization.
	3 Color Tally (15 pin D-Sub connection)

* Tally lamps active when connected to ground

Monitor 3	Monitor	3	Monitor 2	Monitor	2	Monitor 1	Monitor	1
Composite	SDI In		Composite	SDI In		Composite	SDI In
Video In			Video In			Video In

Tally IN

DB-15 Female

Pin1-M3Grn Pin9-Gnd

Pin2-M3Red Pin10-Gnd

Pin3-M3Yel Pin11-M1Grn

Pin4-Gnd Pin12-M2Red

Pin5-Gnd Pin13-M3Yel

Pin6-M2Grn Pin14-Gnd-

Pin7-M2Red Pin15-Gnd

Pin8-M2Yel

Outputs per display	Active Composite loop through BNC.
	Reclocked SDI loop through BNC.
	10 bit Analog composite conversion of SDI signal BNC
Color Bar Signal	Full field SMPTE
Power required	12 V D.C. from external power supply (included) max 3.0 AMP
Operating temperature	320 F to 1100 F (00 C to 450 C)

4Mechanical Specification

Dimensions	19.125”W x 2.5”D x 5.25”H (120cm x 93cm x 25cm)
V-R682P Weight	5.0 lbs (2.27kg)
V-PS12-3.3A Power Supply Weight	1 lbs (0.454kg)

Active	Analog	Active	Analog	Active	Analog	12 VDC from
Output	Output	Output	Output	Output	Output	V-PS12-3.3A
	converted		converted		converted	power supply
	from SDI		from SDI		from SDI	Left Pin - Pos
	Input		Input		Input	Right Pin- Neg

*Composite Video Inputs comply to SMPTE-170M

*SDI inputs comply to SMPTE259M / ITU-R BT601

*Composite Video and SDI Outputs Require Power to be applied for activation

2 V-R563P-SDI Users Guide Marshall Electronics 3