Marshall electronic V-R84DP-SD Switch Settings, Adjustments and Indicators, Operational Setup

10Switch Settings, Adjustments and Indicators

Tally Lamps

5Mechanical Specifications

Dimensions	10.25”w x 7” h x 2.5” d (260.4mm x 215.9mm x 38.1mm)
V-R84DP-SD Weight	4 lbs (1.8 kg)
V-PS12-5V-1 Power Supply Weight	1 lbs (0.45kg)

6Operational Setup

1.Unpack the V-R84DP-SD and accompanying V-PS12-5V-1 power supply. Physically inspect for any damage that may have occurred during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608.

If you are not located within the continental United States call +1 310-333-0606.

2.After inspection, install in your desired location of a standard EIA 19-inch equipment rack.

Adequate ventilation is required when installed to prevent possible damage to the V-R84DP-SD internal components.

3.Connect required cables for signal input and output. Please note that power must be applied to the V-R84DP-SD for all outputs to be activated. All BNC connectors should be rated for 75Ω.

4.Plug the V-PS12-5V-1 power supply into the A.C. source

5.Attach twist lock power connection from V-PS12-5V-1 power supply to the back of the unit.

6.Turn on each of the V-R84DP-SD screens by depressing the power switch located on the front of the unit for each screen.

Dry Erase

7Connectors

*SDI Inputs comply to SMPTE-259M,SDI-270Mbs

*Component Inputs comply to SMPTE274M, 294M, 295M, 296M

*Composite Video Inputs comply to SMPTE-170M

*Tally lamps active when connected to ground

*Battery and External Power can not be used simultaneously

V-Mount Battery Adapter See Optional Accessory section for a selection of batteries

12 VDC from

V-PS12-5V-1 power supply

Active Outputs require

power to be applied

All input signals appear as

output signal

Analog output signals are

buffered and amplified

Tally IN

DB-15 Female

Pin1-Yel	Pin9-
Pin2-Red	Pin10-
Pin3-Grn	Pin11-
Pin4-	Pin12-
Pin5-Gnd	Pin13-
Pin6-	Pin14-
Pin7-	Pin15-Gnd

Screen aspect ratio switch 4:3 or 16:9 selector and indicators	Image Adjustment Controls
	Note: Tint only functions when NTSC
	Video or S-Video are selected

4:3 Aspect 16:9 Aspect

Pin 1 - Neg

Pin 2 - Pos

VGA/XGA Connector

PIN#	SIGNAL	PIN#	SIGNAL
1	RED	9	NC
2	GREEN	10	NC
3	BLUE	11	NC
4	NC	12	NC
5	GND	13	HSYNC
6	RED SHIELD	14	VSYNC
7	GREEN SHIELD	15	NC
8	BLUE SHIELD

DVI-I Connector

Pin#	Signal	Pin#	Signal
1	T.M.D.S DATA 2-	16	HOT PLUG DETECT
2	T.M.D.S DATA 2+	17	T.M.D.S DATA 0-
3	T.M.D.S DATA 2/4	18	T.M.D.S DATA 0+
	SHIELD
4	T.M.D.S DATA 4-	19	T.M.D.S DATA 0/5
			SHIELD
5	T.M.D.S DATA 4+	20	T.M.D.S DATA 5-
6	DDC CLOCK	21	T.M.D.S DATA 5+
7	DDC DATA	22	T.M.D.S CLOCK
			SHIELD
8	ANALOG VERT. SYNC	23	T.M.D.S CLOCK+
9	T.M.D.S DATA 1-	24	T.M.D.S CLOCK-
10	T.M.D.S DATA 1+
11	T.M.D.S DATA 1/3	C1	ANALOG RED
	SHIELD
12	T.M.D.S DATA 3-	C2	ANALOG GREEN
13	T.M.D.S DATA 3+	C3	ANALOG BLUE
14	+5V POWER	C4	ANALOG HORZ SYNC
15	GND	C5	ANALOG GROUND

S-Video Out

4 Pin Din (Female)

Pin1 - GND

Pin2 - GND

Pin3 - Yout

Pin4 - Cout

S-Video In

4 Pin Din (Female)

Pin1 - GND

Pin2 - GND

Pin3 - Yin

Pin4 - Cin

6 V-R824DP-HDS Users Guide MarshallElectronics 3