Matsushita CF-T5LWETZ1 2 12 Replacement Parts List

12 Replacement Parts List

Note : Important Safety Notice

Components identified by mark have special characteristics important for safety.

When replacing any of these components, use only manufacturer's specified parts.

CF-T5LWETZBM

REF. NO and

AREA PART NO. DESCRIPTION Q'TY

Main Block Unit

E1

CR2032/S5Y LITHIUM BATTERY 1

E2

DFJK12U112BB PAD FFC 1

E3

DFJS1050ZA LCD CABLE 1

E4

DFJS958ZB LAN CABLE 1

E5

DFJS980ZA MAIN-SUB CABLE 1

E6 DFJS1020YA DC-IN CABLE 1

E7

DFJS962ZA SP CABLE 1

E8

DFJS973ZB MODEM CABLE 1

E9

DL3UP1534LAA MAIN PWB UNIT(T5MK1 OVERSEAS) RTL 1

E10

DL3UP1443AAA HDD FPC UNIT 1

E11

N1ZYYY000002 ANTENNA PCB-L ASS'Y 1

E12

N1ZYYY000003 ANTENNA PCB-R ASS'Y 1

E13

DL3UP1477AAA 2-PORT USB PWB UNIT 1

E14

K1YYZZ000060 CONNECTOR 1

E15

L0AA01A00018 SPEA KER 1

E17 N0GB1J000012 INVERTOR 1

E18

N2AZZJ000038 KBD US 1

E19

N2EAYYY00008 TOUCH PAD 1

E20

N3CAYYY00006 HDD (60GB) 1

E21

N5HAZ0000014 MDC MODEM 1

E22 N5HZC0000019 WIRELESS LAN MODULE 1

E1010

DFWV08A0087 LCD UNIT ASS'Y 1

E1010-1

DFWV84A0275 TOUCH SCREEN PANEL KIT 1

E1010-1-1

DFWV84A0267 TOUCH SCREEN ASS'Y 1

E1010-1-1-1

DFHR9063ZA PROTECTIVE FILM 1

E1010-1-2

DFHG1824ZA FRONT TP CUSHION A 2

E1010-1-3

DFHG1825YA FRONT TP CUSHION B 2

E1010-1-4

DFHG1826ZA FRONT TP CUSHION C 1

E1010-1-5

DFHG1837ZA FRONT TP CUSHION D 2

E1010-1-6

DFHG1849ZB FRONT TP CUSHION E 1

E1010-2

DFHR3630ZA TS FPC SPACER 1

E1023

DL3UP1567LAA WWAN PWB UNIT RTL 1

E1024

DL3UP1576LAA TS PWB UNIT 1

E1025

DL3UP1577LAA WWAN ANTENNA PCB UNIT(SUB) RTL 1

E1026

DL3UP1578LAA WWAN ANTENNA PCB UNIT(MAIN) RTL 1

E1027

DFJS1048ZA WM CABLE 1

Accessories

A1 CFAA1623AM9 AC ADAPTOR 1

A2 K2CG3DR00003 AC CORD 1

Contents

Main Personal Computer CF-T5 Model No. CF-T5LWETZ1 2 Page Page Page CONTENTS Page Page 2 Names and Functions of Parts N Page Page Page 4.2. Troubleshooting 5 Power-On Self Test (Boot Check) Outline of POST Error Diagnosis by Checking Beep Signal Sound 6 List of Error Codes Page 7 Self Diagnosis Test 1-1. Setting of content of setup 1. Beginning of self-diagnosis test 1-2. When you execute an automatic test 1-3. When you execute the enhancing test 2. Operation of PC-Diagnostic Utility 2-3. The content of the setup is returned to the setting of the user 2-1. Selection of tested device 2-2. "PC-Diagnostic utility" End method 7.1. Test Item and Division of trouble Page 8 Wiring Connection Diagram 9 Disassembly instructions 9.1. Disassembly Flow Chart 9.2.13. Main Unit 9.2.1. 9.2.2. 9.2.3. 9.2.4. 9.2.5. 9.1. Disassembly lnstructions 9.2.1. Preparation 9.2.2. Removing the Keyboard 9.2.4. Removing the Top Case 9.2.3. Removing the HDD 9.2.5. Removing the Touch Pad 9.2.8. Removing the Main Board 9.2.6. Removing the LCD Knob and the Speaker 9.2.7. Removing the USB Board 9.2.9. Removing the Antenna Board (L,R) and the DC-IN Cable 9.2.10. Removing the Wireless LAN Module 9.2.11. Removing the MODEM 9.2.12. Removing the Card Bus Ejector 9.2.13. Removing the LCD Unit 9.2.14. Removing the Hinge Cover 9.2.15. Removing the LCD Unit and the LCD Rear 9.2.16. Removing the Inverter 9.2.17. Removing the WWAN Antenna Board (MAIN), (SUB) 9.2.18. Removing the WWAN Board / LCD Hook WAN 9.3. Reassenbly instructions 9.3.1. Attention when CF-T5L series is repaired 9.3.2.2. Putting Front TP Cushion 9.3.2. Assembly knowhow of the LCD 9.3.2.1. Assembly of the LCD Front 9.3.2.4. Putting LCD Side Dumpers 9.3.2.3. Putting TP Flexible Protection Tape LCD Side Dumper The rib match of thick one. LCD insulator LCD insulator 9.3.2.6. Assembly of the LCD Dumper 9.3.2.5. Assembly of the LCD Unit 9.3.2.7. Connecting LCD Cable 9.3.2.8. Assembly of the Inverter and Putting Inverter Tapes 9.3.2.9. Line processing LCD cable (1) 9.3.2.10. Putting PET Tape HINGE L 9.3.2.11. Line processing LCD cable (2) All the signal lines are processed the conductive cloth internally. PET TAPE Safety work Safety work 9.3.2.12. Putting Tape of LCD Cable 9.3.2.13. Assembly of the Pen Holde Page LCD REAR WAN LCD REAR CUSHION LCD REAR CUSHION 9.3.2.14. Putting LCD Rear Cushions 9.3.2.15. Assembly of the WM Cable 9.3.2.16. Assembly of the WWAN Board 9.3.2.17. Putting Tapes for WM Cable 9.3.2.18. Assembly of the WWAN Antenna Board (MAIN), (SUB) 9.3.2.19. Assembly of the Hinge Cover (L), (R) 9.3.2.20. Putting Productive Film 9.3.3. Assembly knowhow of the Main Board 9.3.3.1. Putting tapes for Memory Sheet of top side 9.3.3.2. Assembly of the MDC MODEM Safety work Safety work 9.3.3.3. Putting PET tapes 9.3.3.4. Assembly of the PCMCIA Ejector 9.3.3.5. Assembly of the LAN Cable Safety Work Safety work 2 3mm 2 3mm 9.3.3.6. Line processing LAN cable (Safety work) Affixation load of affixation thing not instructed : More than 1kgf/c 9.3.3.7. Assembly of the W-LAN Module / Putting Memory Sheet < Attention > 9.3.3.8. Putting Sheets 9.3.3.9. Assembly of the W-LAN Sheet 9.3.3.10. Assembly of the HDD FPC HDD FPC PET Tape Watching confirmation of insertion in silk line 9.3.3.12. Setting the Main Board 9.3.3.11. Assembly of the DC-IN Cable Safety work Main Board Running aground of shutter to bottom Confirm, and install the turning off position (left side) Main Boards W-LAN SW. 9.3.4. Assembly knowhow of the Top Case 9.3.4.1. Assembly of the Speaker 9.3.4.2. Line processing Speaker Cable and putting Speaker Sheet 9.3.4.3. Putting HDD Dumper, Hinge Buckup Sheet and Spacer Washer etc. Put the Washer Do not close the screw hole Spacer Washer 9.3.4.4. Assembly of the LCD Knob Difference match (Gap 0.5mm or less) The spring is hung. The hook is inserted while doing the slide. Rib match (Gap 0.5mm or less) Sheet Put on the case before inserting the knob Page 9.3.5. Assembly knowhow of the Bottom Case 9.3.5.1. Setting Antenna Board and Line processing (1) 9.3.5.2. Assenbly of the Antenna Cover (L) Antenna Cover (L) Antenna Board (L) 9.3.5.3. Line processing LAN Cable / USB Cable / MODEM Cable 9.3.6. Assembly knowhow of the Body 9.3.6.1. Setting LCD 9.3.6.2. Line processing LCD Cable (bottom case side) Conductive Cloth is wrapped. LCD UNIT 9.3.6.3. Line processing Relay Cable 9.3.6.4. Putting Line Hold Sheet WWAN 9.3.6.5. Assembly of the Top Case 9.3.6.6. Assembly of the Keyboard 3.Bend of two sided tape putting and KB FPC KB Plate assembly 2.Both sides tape affixation 1. 9.3.6.7. Assembly of the Heat Spreader and Side Cover R 9.3.6.8. Setting Keyboard 9.3.6.9. Setting DIMM Cover DIMM Cover 9.3.6.10. The tightening screw of Bottom Case Screw A Screw A (XSB2+4FNL) is tightened. 9.3.6.11. Putting Sheets 9.3.6.12. Setting Knobs 9.3.6.13. Putting RJ Cover and Labels 9.3.6.14. Assembly of the HDD / HDD Cover 9.3.6.15. Putting HDD Cover Heat Sheet and Bottom Heat Sheet LCD Front Be parallel after putting. LCD Rubber Width : large Width : small Screws (DXHM0039ZA) are tightened. LCD Rubbers (DXHM0039ZA) are pasted. 9.3.6.16. Putting Tapes for WWAN Antenna Cable 9.3.6.17. Assembly of the LCD Rear 9.3.6.18. Assembly of the WWAN Module 10 Exploded View 10.1. Display Section 10.2. LCD Unit Assy / Pen Holder Section 10.3. Cabinet Section 10.4. Bottom Section 12 Replacement Parts List CF-T5LWETZBM Page Page Page Re p lacement Parts List A CF-T5LWETZBM (06-10-27) PART NO. DESCRIPTION Q'TY MAIN PCB Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page USB PCB TS PCB WWAN PCB