AMPLIFIER FEATURE DESCRIPTIONS
POWER ONE AMPLIFIERS:
!Each model is capable of 4 &
!The input sensitivities for rated output powers are variable from 0.2V to 6V on all models.
!All crossovers are fully variable in their respective ranges.
!Crossover filters are 12dB/Octave.
!A POWER LED indicates the powered up and turned on condition.
!All Crunch amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, and amplifier DC faults indicated by the red “PROTECT” LED.
!CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4 and
L L
LEVEL | BASS EQ | HPF | LPF | MODE | |
+ - gnd - + |
|
|
|
|
|
HI INPUT |
|
|
|
|
|
6V 0.2V | 0dB 12dB | 60Hz 12KHz | 30Hz 250Hz | FULL LPF HPF | MONO STEREO |
R R
LINE OUT LINE INPUT
The
MODE: The mode switch allows you to choose Stereo for full range 2 channel operation or MONO for bridging operation
HIGH INPUT: If your radio/CD player does not have unbalanced (RCA) outputs, you can use the HIGH level (wire) inputs.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain multiple amplifiers from one signal.
Note that the LOW PASS signal is MONO.
| MODE |
|
| HIGH INPUT | ||||||
|
| + - GND - + + - GND - + | ||||||||
|
|
|
|
| CH1 |
| CH3 | |||
|
|
|
|
|
|
|
|
| ||
| 2 | 3 | 4 | LPF | HPF FULL |
| FULL HPF LPF CH1 | CH2 | CH3 CH4 | |
|
|
|
|
| ||||||
LPF | HPF | BASS EQ | LEVEL |
| LEVEL BASS EQ | HPF | LPF | |||
|
|
|
|
| CH2 | INPUT OUTPUT INPUT | CH4 |
|
|
|
30Hz 250Hz | 60Hz 12KHz | 0dB 12dB | 6V 0.2V | 6V 0.2V 0dB 12dB 60Hz 12KHz 30Hz 250Hz | ||||||
| CHANNEL 1 / 2 |
|
|
| CHANNEL 3 / 4 |
|
The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of controls. 1 set for channels 1 & 2 and 1 set for channels 3 & 4.
In addition, the 4 channel models have a Mode switch which allows you to select 2, 3 or 4 channel operation. Switch to 2 channel if you only have 1 set of RCA’s in CH 1/2 and the unit will automatically supply signal to channels 3/4. Select 3 channel when you only have RCA’s in CH 1/2 but plan to run channels 3/4 bridged. Select 4 channel if you are providing RCA’s to channels 1/2 and 3/4.
The
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain multiple amplifiers from one signal.
Note that the LOW PASS signal is MONO.
| REMOTE | BASS | SUB | LOW | OUTPUT | INPUT |
POWER | CONTROL | BOOST | SONIC | LEVEL | L | L |
PASS | ||||||
PROTECT |
| 0dB 12dB | 15Hz 55Hz | 40Hz 150Hz 6V 0.2V | R | R |
|
|
LEVEL: Adjusts the input sensitivity from 0.2 volts to 6 volts.
BASSBOOST: 45Hz bass boost adjustable from 0db to 12dB.
REMOTE CONTROL: This is the input jack for the remote Level control.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain multiple amplifiers from one signal.
The mono amps are capable of 4, 2 &
Operating the amp below
|
|
|
|
| ||||||||||
|
|
|
|
| 3/4 CH CONTROLS |
|
| 1/2 CH CONTROLS |
| |||||
| CH5 | CH4 | CH2 | LEVEL |
|
| HPF | MODE | LEVEL |
| HPF | REMOTE | ||
INPUT | L |
|
| 6V | 0.2V | FULL | HPF | 10Hz 150Hz | 4CH | 5CH | 6V 0.2V | FULL | HPF 10Hz 150Hz |
|
|
|
|
| |||||||||||
R |
|
|
|
|
|
|
|
|
| |||||
|
|
| 6V | 0.2V |
|
| 15Hz 55Hz |
|
| 0dB 12dB |
| 30Hz 150Hz | POWER | |
| CH5 | CH3 | CH1 |
|
|
|
|
| ||||||
| LEVEL |
|
| SUBSONIC |
|
| BASS EQ |
| LPF | PROTECT | ||||
|
|
|
|
|
|
|
| 5 CH CONTROLS |
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
The 5 channel amp have the same features as the 4 channel models accept that there is an additional set of controls for channel 5 The
MODE: The mode switch allows you to choose 4 or 5 channel operation.
LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
SUBSONIC: Is adjustable from 15Hz to 55Hz for the channel 5 only.
BASS EQ: Is adjustable from 0dB to 12dB for channel 5 only.
REMOTE: this is used for the Bass Remote module.
2