TROUBLESHOOTING cont.
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service call...In U.S.A. http://www.maytag.com/help - In Canada www.maytag.ca
| If you experience | Possible Causes | Solution |
| Dryer displaying code | “PF” (power failure), | Was the drying cycle interrupted by a power failure? |
| message | Start LED flashes | Press START/PAUSE to restart the dryer. |
|
| ||
|
|
|
|
|
| “F# E#” (F1 E1, F3 E1, etc.) variable | If a code beginning with an “F” appears in the display. |
|
| service codes. | Alternating between F# and E#, the dryer control has detected |
|
|
| a problem that requires service. Call for service. |
|
|
|
|
| Cycle time too short | Sensor cycle ending early. | The load may not be contacting the sensor strips. Level the dryer. |
|
|
| Use Timed Dry for very small loads. Change the dryness level |
|
|
| setting on Sensor Cycles. |
|
|
| Increasing or decreasing the dryness level will change the amount |
|
|
| of drying time in a cycle. If loads are consistently ending too early, |
|
|
| see also Changing the Sensor Dry Default Settings. |
|
|
|
|
| Lint on load | Lint screen clogged. | Lint screen should be cleaned before each load. |
|
|
|
|
| Stains on load or drum | Dryer fabric softener not properly | Add dryer fabric softener sheets at the beginning of the cycle. |
|
| used. | Fabric softener sheets added to a partially dried load can stain |
|
|
| your garments. |
|
|
| Drum stains are caused by dyes in clothing (usually blue jeans). |
|
|
| These will not transfer to other clothing. |
|
|
|
|
| Loads are wrinkled | Load not removed from dryer at the | Select Touch Up Cycle to tumble the load with water and heat. |
|
| end of the cycle. | This cycle is best for smoothing out wrinkles and reducing odors |
|
|
| from loads consisting of |
|
|
| blends, common knits and synthetic garments. |
|
|
| NOTE: Refer to garment care label instructions. Dry clean only |
|
|
| garments are not recommended. |
|
|
|
|
|
| Dryer overloaded. | Dry smaller loads that can tumble freely. |
|
|
|
|
| Odors | Have you recently been painting, | If so, ventilate the area. When the odors or fumes are gone from |
|
| staining, or varnishing in the area | the area, rewash and dry the clothing. |
|
| where your dryer is located? |
|
|
|
|
|
|
| Is the electric dryer being used for the | The new electric heating element may have an odor. The odor will |
|
| first time? | be gone after the first cycle. |
| Load is too hot | Were laundry items removed from | Allow the Cool Down cycle to finish before removing laundry |
|
| the dryer before the end of the cycle? | from dryer. All cycles are cooled slowly to reduced wrinkling and |
|
|
| make it easier to handle. Items removed before Cool Down may |
|
|
| feel very warm. |
|
|
|
|
|
| Was a high temperature cycle used, | Select a lower temperature, and use a sensor drying cycle. These |
|
| or was a separate temperature | cycles sense the temperature or the moisture level in the load and |
|
| control set on high? | shut off when the load reaches the selected dryness. This reduces |
|
|
| overdrying. |
|
|
|
|
13
