n.CE n. | CLEAR ESCROW OPTION |
| When selected, money held in escrow for 30 minutes without further escrow |
| or cycle activity will be cleared. |
00 | Not Selected “OFF.” |
CE | Selected “ON.” |
| Press DELICATES & KNITS keypad once for this selection. |
| Press WOOLENS keypad once to advance to next code. |
r.800 r. TOP SPIN SPEED RPM
800This can be selected from the following spin speeds: 600 rpm, 750 rpm, 800 rpm, 1000 (displays as 999) rpm.
Step between speeds by pressing PERMANENT PRESS. Currently set for 800 rpm.
Press WOOLENS keypad once to advance to next code.
U.00 U. PENNY INCREMENT OFFSET
00This represents the penny increment price offset used in
Generation 2 (Enhanced Debit) PR models. Choose from
Press WOOLENS keypad once to advance to next code.
A1.00 A1. PREWASH LENGTH
00This is the number of minutes of PREWASH.
Choose 0 to disable the prewash or select between 2 and 7 minutes by pressing the PERMANENT PRESS keypad.
Press WOOLENS keypad once to advance to next code.
A2.03 A2. FINAL SPIN LENGTH
03This is the number of minutes of final high speed spin. Choose from
Press WOOLENS keypad once to advance to next code.
If cycle counter (90C) is selected, the following is true:
100 | Represents the number of cycles in HUNDREDS | 1 02 | = 200 |
200 | Represents the number of cycles in ONES | 2 25 | = 25 |
Total = 225 cycles
This is “VIEW ONLY” and cannot be cleared.
Press WOOLENS keypad once to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following is true:
300 | Number of dollars in HUNDREDS | 3 01 | = 100 |
400 | Number of dollars in ONES | 4 68 | = 68 |
500 | Number of CENTS. | 5 75 | = 75 |
Total =$168.75
END of SETUP PROCEDURES.
EXIT FROM SETUP MODE
PD Models: Reinstall access door.
PR Model: Remove power, open console, reinsert plug into AA1, close console, and apply power.
Washer Diagnostic Mode
To enter the “Washer Diagnostic Mode,” first enter “Start Operating Setup.” Then press and hold the DELICATES & KNITS key for 1 second while in any of the setup codes one through six, anytime a diagnostic code is present, or while dAS displays if operating with Maytag Data Acquisition setup.
On entry to diagnostic mode the entire display will flash, a cycle in process is canceled, money in escrow is cleared, and diagnostic codes are cleared. If a diagnostic code persists, it must be corrected before the following cycle options are permitted.
There are five possible ways to initiate cycle activity from diagnostic mode as follows:
1.Clean Washer cycle - With the entire display flashing, this cycle is started by pressing the BRIGHTS keypad.
Use the Clean Washer cycle once a month to keep the inside of your washer fresh and clean. This cycle uses a higher water level. Use with AFFRESH™ washer cleaner tablet or liquid chlorine bleach to thoroughly clean the inside of your washing machine. This cycle should not be interrupted. See “Cleaning Your Washer.”
IMPORTANT: Do not place garments or other items in the washer during the Clean Washer cycle. Use this cycle with an empty wash drum.
2.Cycle Credit - With the entire display flashing, a cycle may be credited by pressing the PERMANENT PRESS keypad (CC will display). When the service mode is exited “SELECT CYCLE” will be displayed unless the
3.Manual Load Test Cycle - With the entire display flashing, this cycle is started by pressing the WHITES keypad. This cycle provides more typical full length fills, tumbles, drains and actuator dispenser movement allowing for a more thorough analysis of the washer operation, including pressure switch behavior.
4.Quick Spin Cycle - With the entire display flashing, this cycle is started by pressing the COLORS keypad. This cycle provides a method to quickly drain and spin (remove water from the washer) if desired.
5.History Overview Test Cycle - With the entire display flashing, this cycle is started by pressing the WOOLENS keypad. This cycle provides a quick verification that the cold and hot water valves, dispensers, and pump motor are working and actuator dispenser movement. It also includes drain and spin operations.
Pressing the DELICATES & KNITS keypad will exit diagnostic mode and cancel a diagnostic cycle in process.
16
