Troubleshooting a system

AFTER INSTALLATION

Setting up systems after installation for best performance

General:

As mentioned in the “General Installation Notes” section, the system should now be powered up, and working. At this point, all crossover frequency and input selection switches should be properly set for the application, and all volume, level and equalizer controls turned to minimum.

Level control setup:

Insert a CD or cassette that you are familiar with to use as a reference, and turn the head unit volume control to about 80% of its full setting. The system sound level will of course be very low, and the following procedures will help you to match the ampliﬁer input sensitivities properly to the head unit output signal level.

Single 2 channel ampliﬁer systems (RAB 250):

Turn the level control up slowly, till you hear distortion, then back off a few degrees on the control.

Single 4 channel ampliﬁer systems (RAB 450):

Turn the channel 1&2 level control up slowly, till you hear distortion, then back off a few degrees on the control. Repeat for channel 3&4.

2 or 3 way active systems (all):

Always start with the bass, or low frequency ampliﬁer as a reference, by turning its control up to the point where distortion is audible, and back it off some.

Now adjust the level control for the highs or tweeter channels in a 2 way active system, to balance the highs to lows.

In a 3 way active system, match the midrange level to the bass, and then the highs to the midrange and bass. It may be necessary to perform a few iterations of the midrange and highs level control settings to achieve a satisfactory sound balance.

Crossover frequency ﬁne tuning:

We had started off in the “General Installation Notes” section by setting crossover frequency controls to approximate positions, and now you can adjust these for best sound quality. Be careful not to stray too far from those crossover frequencies as recommended by the loudspeaker manufac- turer, as it is quite possible to damage midrange and tweeters with excess power outside their nominal operating frequency ranges.

Equalizer setup:

Once all levels and crossover frequencies have been set for a pleasant sound balance, we can start equalizing the system frequency response. It is important to remember that a boost applied at any frequency, or range of frequencies, will cause severe ampliﬁer clipping. The following comments apply to ALL equalizers and tone controls on the ampliﬁers, as well as those on head units and dash mount equalizers.

Use the head unit volume control to adjust the system to an intermediate level, and proceed to adjust equalizers and tone controls to personal taste. Now go back to the Level control setup above, and readjust all level controls.

Sit back and enjoy the music!

English

The key to ﬁnding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault.

Description of the Diagnostic system built into all MB QUART ampliﬁers:

The diagnostic system will shut down the ampliﬁer, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel DIAGNOSTIC LED lighting up under the following conditions:

1 - A short circuit on the loudspeaker leads.

2 - An internal ampliﬁer fault that causes a DC offset on the loudspeaker output.

Should the ampliﬁer go into diagnostic mode, simply disconnect all RCA and speaker leads, while keeping +12 volt, power ground and remote leads connected. Now turn the ampliﬁer back on, and if the diagnostic LED lights, the ampliﬁer has an internal fault.

If not, plug the RCA cables back, and reset the ampliﬁer. If it goes into diagnostic now, the fault lies in the input, either with bad cables or source unit. If the ampliﬁer seems ﬁne with RCA cables plugged in, connect the speakers, one at a time, and if one of the speakers or its wiring is faulty, it will activate the diagnostic system.

RAB 1450 specifications

The MB Quart RAB 1450 is a formidable addition to the realm of automotive audio systems, specifically designed for drivers who demand both high performance and clarity in their sound experience. Known for its robust construction and innovative technologies, this amplifier is an ideal choice for those looking to upgrade their vehicle's audio system.

One of the standout features of the RAB 1450 is its power output. With a peak power of 1450 watts, this amplifier ensures that every note, from the deepest bass to the highest treble, is delivered with exceptional clarity and intensity. It operates efficiently with a Class D design, which not only produces powerful sound but also keeps heat generation at manageable levels. This means that users can enjoy extended listening sessions without worrying about overheating or performance degradation.

The RAB 1450 is equipped with a variable low-pass crossover, allowing users to customize their audio experience by controlling which frequencies are sent to their subwoofers. This feature is particularly beneficial for those who like to fine-tune their sound to match their personal preferences or their vehicle's acoustic characteristics.

Another notable characteristic of the RAB 1450 is its built-in protection circuitry. This feature safeguards the amplifier against potential damage from overloads or short circuits, ensuring a long lifespan and reliable performance. Additionally, the amplifier has adjustable gain control that helps users optimize the output level for their specific audio setup, enhancing both sound quality and clarity.

The construction of the RAB 1450 is designed with durability in mind. Featuring a sleek and rugged chassis, it withstands the rigors of automotive environments. The amplifier also utilizes high-quality components that enhance sound quality and reliability.

Installation is made easy with user-friendly connections and a compact size that fits in most vehicles without hassle. The MB Quart RAB 1450 is not just an amplifier; it represents a commitment to quality and performance, making it an exceptional choice for any audiophile seeking to elevate their mobile sound system.

In conclusion, the MB Quart RAB 1450 stands out in the crowded marketplace of car audio amplifiers with its powerful output, advanced features, and dependable construction. It is a prime choice for those who desire an immersive and customizable listening experience while on the road.

MB QUART RAB 1450 manual Setting up systems after installation for best performance

Models: RAB 1450