To Remove Wheels See Fig, Carburetor | McCulloch 96192004102

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 21

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 22)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 22

17

Image 17

McCulloch 96192004102 owner manual To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Contents

MC627ES Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEY Electric start button used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting Exploded KEY Part Description Scraper BAR Auger HousingAuger 27 LH Auger 27 RH Bearing Plug Auger BearingSkid Plate LH Skid Plate RH Deflector Weldment Chute WeldmentDeflector Seal Strap Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator Head Handle Grip 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHLower Handle Pivot Support Weldment Retainer SpacerKnob RED Handle Knob Traction ROD Impeller RODShifter ROD TOP Shifter ROD Bottom Console Panel Wire HarnessHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number MC627ES Drive Drive Plate Assembly AssemblySpeed Selector Rubber Ring Roll PIN 3/16 Axle ShaftSprocket Clik PIN Frame Complete LCT Engine427963X428 Engine Mounting Plate Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley 432332X421 Wheel Assembly LH432331X421 422663 Safety Ignition KEY DECAL, Danger 181037 Service Notes Service Notes Limited Warranty