3 - ASSEMBLY INSTRUCTIONS
3 - ASSEMBLY INSTRUCTIONS
TO INSTALL SAW CHAIN:
WARNING
Always wear heavy duty gloves when handling saw chain or making saw chain adjustments.
1.Spread chain out in a loop with cutting edges (A) pointing CLOCKWISE around loop (Figure
2.Slip the chain around the sprocket (B) behind the clutch (C). Make sure the links fit between the sprock- et teeth (Figure
3.Guide the drive links into the groove (D) and around the end of the bar (Figure
NOTE: The saw chain may droop slightly on the lower part of bar. This is normal.
3-4. SAW CHAIN TENSION ADJUSTMENT
Proper tension of saw chain is extremely important and must be checked before starting, as well as during any cut- ting operation.
Taking the time to make needed adjustments to the saw chain will result in improved cutting performance and pro- longed chain life.
WARNING
Always wear heavy duty gloves when handling saw chain or making saw chain adjustments.
TO ADJUST SAW CHAIN:
1. Hold nose of guide bar up and turn adjustment screw |
(D) CLOCKWISE to increase chain tension. Turning |
screw COUNTERCLOCKWISE will decrease amount |
CAUTION
A new saw chain stretches, requiring adjustment after as few as 5 cuts. This is normal with a new chain, and the interval between future adjustments will lengthen quickly.
CAUTION
If saw chain is TOO LOOSE or TOO TIGHT, the sprocket, bar, chain, and crankshaft bearings will wear more rapidly. Study Figure
To Test CHAIN BRAKE®:
1.The CHAIN BRAKE® is DISENGAGED (chain can move) when BRAKE LEVER IS PULLED BACK AND LOCKED. Be sure the chain break latch is in the on position. (Figure
2.The CHAIN BRAKE® is ENGAGED (chain is stopped) when brake lever is in forward position and the chain brake latch is in the off position. You should not be able to move chain (Figure
NOTE: The brake lever should snap into both positions. If strong resistance is felt, or lever does not move into either position, do not use your saw. Take it immediately to an Authorized Service Center for repair.
4.Pull guide bar forward until chain is snug. Ensure all drive links are in the bar groove.
5.Install the clutch cover making sure the tang is posi- tioned in the lower hole in the guide bar. Make sure the chain does not slip off of the bar. Install the bar retaining nuts hand tight and follow tension adjust- ment instructions in Section
NOTE: The guide bar retaining nuts are installed only hand tight at this point because saw chain adjustment is required. Follow instructions in Section
A
B
D
C
of tension on chain. Ensure the chain fits snugly all the |
way around the guide bar (Figure |
2. After making adjustment, and while still holding nose |
of bar in the uppermost position, tighten the bar |
retaining nuts securely. Chain has proper tension |
when it has a snug fit all around and can be pulled |
around by gloved hand.
NOTE: If chain is difficult to rotate on guide bar or if it binds, too much tension has been applied. This requires minor adjustment as follows:
A.Loosen the bar retaining nuts so it is finger tight. Decrease tension by turning the bar adjustment screw COUNTERCLOCKWISE slowly. Move chain back and forth on bar. Continue to adjust until chain rotates freely, but fits snugly. Increase tension by turning bar adjustment screw CLOCKWISE.
B.When saw chain has proper tension, hold nose of bar in uppermost position and tighten the bar retaining nut securely.
D
ABC
3-5. CHAIN BRAKE® MECHANICAL TEST
Your chain saw is equipped with a CHAIN BRAKE® that reduces possibility of injury due to kickback. The brake is activated if pressure is applied against brake lever when, as in the event of kickback, operator’s hand strikes the lever. When the brake is actuated, chain movement stops abruptly.
WARNING
The purpose of the CHAIN BRAKE® is to reduce the possi- bility of injury due to kickback; however, it cannot provide the intended measure of protection if the saw is operated carelessly.
Always test the CHAIN BRAKE® before using your saw and periodically while on the job.
ON
OFF
8
9
