5 - OPERATING INSTRUCTIONS
6 - GENERAL CUTTING INSTRUCTIONS
5-3. RE-STARTING A WARM ENGINE
1.Make sure the on/off switch is in the “I” position.
2.Pull out the choke to the point where it latches in place.
3.Depress the primer bulb 10 times.
4.Set the throttle latch.
5.Pull the starter rope rapidly 4 times. The engine should start.
6.Push in the choke as far it will go.
7.Release the throttle latch.
5-4. TO STOP ENGINE
1.Release trigger and allow engine to return to idle speed.
2.Press STOP switch down to stop engine Figure
WARNING
Activate the CHAIN BRAKE® slowly and deliberately. Keep the chain from touching anything; don’t let the saw tip for- ward.
6.Chain should stop abruptly. When it does, immediately release the throttle trigger.
WARNING
If chain does not stop, turn engine off and take your unit to the nearest Authorized Service Center for service.
7.If CHAIN BRAKE® functions properly, turn the engine off and return the CHAIN BRAKE® to the DISEN- GAGED position.
A BC
6-1.FELLING
Felling is the term for cutting down a tree. Small trees up to
FELLING A TREE:
WARNING
A retreat path (A) should be planned and cleared as nec- essary before cuts are started. The retreat path should extend back and diagonally to the rear of the expected line of fall, as illustrated in Figure
CAUTION
If felling a tree on sloping ground, the chain saw operator should keep on the uphill side of the terrain, as the tree is likely to roll or slide downhill after it is felled.
NOTE: Direction of fall (B) is controlled by the notching cut. Before any cuts are made, consider the location of larger branches and natural lean of the tree to determine the way the tree will fall.
WARNING
Do not cut down a tree during high or changing winds or if there is a danger to property. Consult a tree professional. Do not cut down a tree if there is a danger of striking utility wires; notify the utility company before making any cuts.
FELLING CUT:
1.Use wooden or plastic wedges (G) to prevent binding the bar or chain (H) in the cut. Wedges also control felling (Figure
2.When diameter of wood being cut is greater than the bar length, make 2 cuts as shown (Figure
WARNING
As the felling cut gets close to the hinge, the tree should begin to fall. When tree begins to fall, remove saw from cut, stop engine, put chain saw down, and leave area along retreat path (Figure
B
A
INERTIA CHAIN BRAKE® ACTION :
NOTE: THIS SAW IS EQUIPPED WITH AN INERTIA CHAIN BRAKE.IF THE SAW KICKS BACK WHILE IN USE, THE INERTIA OF THE MOVING SAW WILL ACTIVATE THE BRAKE. A BRAKE BAND AROUND THE CLUTCH DRUM ACTIVATES AND STOPS THE MOVING CHAIN.
5-5.CHAIN BRAKE® OPERATIONAL TEST
Test the CHAIN BRAKE® periodically to ensure proper function.
Perform a CHAIN BRAKE® test prior to initial cutting, follow- ing extensive cutting, and definitely following any CHAIN BRAKE® service.
TEST CHAIN BRAKE® AS FOLLOWS:
1.Place saw on a clear, firm, flat surface.
2.Start engine.
3.Grasp the rear handle (A) with your right hand (Figure
4.With your left hand, hold the front handle (B) [not CHAIN BRAKE® lever (C)] firmly (Figure
5.Squeeze the throttle trigger to 1/3 throttle, then imme- diately activate the CHAIN BRAKE® lever (C) (Figure 5- 5A).
12
5-6.SAW CHAIN / BAR LUBRICATION
Adequate lubrication of the saw chain is essential at all times to minimize friction with the guide bar.
Never starve the bar and chain of oil. Running the saw with too little oil will decrease cutting efficiency, shorten saw chain life, cause rapid dulling of chain, and cause exces- sive wear of bar from overheating. Too little oil is evidenced by smoke, bar discoloration or pitch
NOTE: Saw chain stretches during use, particularly when it is new, and it will occasionally be necessary to adjust and tighten it. New chain will require adjustment after about 5 minutes of operation.
5-7.AUTOMATIC OILER
Your chain saw is equipped with an automatic clutch driven oiler system. The oiler automatically delivers the proper amount of oil to the bar and chain. As the engine speed increases, so does the oil flow to the bar pad. There is no flow adjustment. The oil reservoir will run out at approxi- mately the same time as the fuel supply runs out.
GENERAL GUIDELINES FOR FELLING TREES:
Normally felling consists of 2 main cutting operations, notching (C) and making the felling cut (D).
Start making the upper notch cut (C) on the side of the tree facing the felling direction (E). Be sure you don t make the lower cut too deep into the trunk.
The notch (C) should be deep enough to create a hinge (F) of sufficient width and strength. The notch should be wide enough to direct the fall of the tree for as long as possible.
WARNING
Never walk in front of a tree that has been notched.
Make the felling cut (D) from the other side of the tree and
1.5- 2.0 inches
Never saw completely through the trunk. Always leave a hinge. The hinge guides the tree. If the trunk is completely cut through, control over the felling direction is lost.
Insert a wedge or felling lever in the cut well before the tree becomes unstable and starts to move. This will prevent the guide bar from binding in the felling cut if you have mis- judged the falling direction. Make sure no bystanders have entered the range of the falling tree before you push it over.
WARNING
Before making the final cut, always recheck the area for bystanders, animals or obstacles.
13
GH