![](/images/new-backgrounds/1103795/10379515x1.webp)
6 - GENERAL CUTTING INSTRUCTIONS
7 - MAINTENANCE INSTRUCTIONS
6-2. LIMBING
Limbing a tree is the process of removing the branches from a fallen tree. Do not remove supporting limbs (A) until after the log is bucked (cut) into lengths (Figure
WARNING
Never cut tree limbs while standing on tree trunk.
A
6-3. BUCKING
Bucking is cutting a fallen log into lengths. Make sure you have a good footing and stand uphill of the log when cutting on sloping ground. If possible, the log should be supported so that the end to be cut off is not resting on the ground. If the log is supported at both ends and you must cut in the middle, make a downward cut halfway through the log and then make the undercut. This will prevent the log from pinching the bar and chain. Be careful that the chain does not cut into the ground when bucking as this causes rapid dulling of the chain.
When bucking on a slope, always stand on the uphill side.
1.Log supported along entire length: Cut from top (over- buck), being careful to avoid cutting into the ground (Figure
2.Log supported on 1 end: First, cut from bottom (under- buck) 1/3 diameter of log to avoid splintering. Second, cut from above (overbuck) to meet first cut and avoid pinching (Figure
3.Log supported on both ends: First, overbuck 1/3 diam- eter of log to avoid splintering. Second, underbuck to meet first cut and avoid pinching (Figure
NOTE: The best way to hold a log while bucking is to use a sawhorse. When this is not possible, the log should be raised and supported by the limb stumps or by using sup- porting logs. Be sure the log being cut is securely support- ed.
6-4.BUCKING USING A SAWHORSE
For personal safety and ease of cutting, the correct position for vertical bucking is essential (Figure
VERTICAL CUTTING:
A.Hold the saw firmly with both hands and keep the saw to the right of your body while cutting.
B.Keep the left arm as straight as possible.
C.Keep weight on both feet.
CAUTION
While the saw is cutting, be sure the chain and bar are being properly lubricated.
B
A
C
All chain saw service, other than items listed here in your user manual maintenance
instructions, should be performed by your nearest Authorized Service Center.
7-1.PREVENTIVE MAINTENANCE
A good preventive maintenance program of regular inspection and care will increase life and improve performance of your McCulloch chain saw. This maintenance checklist is a guide for such a program.
Cleaning, adjustment, and parts replacement may be required, under certain conditions, at more frequent intervals than those indicated.
MAINTENANCE CHECKLIST |
|
| HOURS OF | ||
EACH USE |
| OPERATION | |||
|
|
| |||
ITEM | ACTION |
| 10 |
| 20 |
|
|
|
|
|
|
SCREWS / NUTS / BOLTS | INSPECT / TIGHTEN | ✔ |
|
|
|
|
|
|
|
|
|
AIR FILTER | CLEAN OR REPLACE |
| ✔ |
|
|
|
|
|
|
|
|
FUEL FILTER / OIL FILTER | REPLACE |
|
|
| ✔ |
|
|
|
|
|
|
SPARK PLUG | CLEAN / ADJUST / REPLACE |
| ✔ |
|
|
|
|
|
|
|
|
| INSPECT | ✔ |
|
|
|
SPARK ARRESTER SCREEN |
|
|
|
|
|
REPLACE AS REQUIRED |
| ✔ |
|
| |
|
|
|
| ||
|
|
|
|
|
|
| INSPECT | ✔ |
|
|
|
FUEL HOSES |
|
|
|
|
|
*REPLACE AS REQUIRED |
|
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
| INSPECT | ✔ |
|
|
|
CHAIN BRAKE® COMPONENTS |
|
|
|
|
|
*REPLACE AS REQUIRED |
|
|
|
| |
|
|
|
|
| |
|
|
|
|
|
|
*Recommended for Maintenance by a Authorized Service Center Technician. |
|
| |||
|
|
|
|
|
|
14
15