OPERATING INSTRUCTIONS

IMPORTANT POINTS

SAllow the cutting blades to reach full speed before entering the material to be cut.

SNever attempt to use this hedge trimmer to cut hedges that have any branches with a diameter larger than 1 cm.

OPERATING POSITION

Hearing

Protection Eye

Protection

3.Engage the choke lever with the throttle lever by moving the choke lever to the FULL CHOKE position until it clicks.

Primer Bulb

Choke

 

 

Lever

STOPPING YOUR ENGINE

DTo stop engine, move the ON/OFF switch to OFF position.

STARTING YOUR ENGINE

DFuel engine. Move at least 10 feet (3 meters) away from the fueling site.

DHold the unit on the ground in the starting po- sition as shown. Support unit so the blade is off of the ground and away from trees,

bushes, onlookers, etc.

D This unit is designed to start at a fast idle speed without blade movement. The speed is controlled by the choke lever.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

ON OFF

Switch Throttle

Lock--out

Throttle Trigger

NOTE: In the following steps, when the choke lever is moved to the FULL CHOKE position until it clicks, the correct throttle set- ting for starting is set automatically.

1.Move the ON/OFF switch to the ON posi- tion.

2.Slowly press the primer bulb 6 times.

4.Pull starter rope handle sharply until en- gine sounds as if it is trying to run, but do not pull rope more than 6 times.

5.Move the choke lever to the HALF CHOKE position.

6.Pull starter rope sharply until the engine runs, but no more than 6 pulls. If the en- gine doesn’t start after 6 pulls (at the HALF CHOKE position), check to make sure the ON/OFF switch is in the ON posi- tion. Move the choke lever to the FULL CHOKE position until it clicks to reset the throttle and press the primer bulb 6 times; pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 more pulls. NOTE: If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

7.Once the engine starts, allow the engine to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at the OFF CHOKE position before squeezing the throttle trigger to run engine at full speed. NOTE: If engine dies with the choke lever in the OFF CHOKE position prior to pulling the trigger, move the choke lever to the HALF CHOKE position and pull the rope until the engine runs, but no more than 6 pulls. If the engine dies while squeezing the throttle trigger, move the choke lever to the FULL CHOKE position until it clicks to reset the throttle; then move the choke lever to the HALF CHOKE position and pull the rope until the engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the ON/OFF switch to the ON posi- tion.

2.Slowly press the primer bulb 6 times.

3.Move the choke lever to the FULL CHOKE position until it clicks to reset the throttle; then move the choke lever to the HALF CHOKE position.

4.Pull starter rope sharply until engine runs, but no more than 5 pulls.

-- 6 --

Page 5 Page 7
Page 6
Image 6
McCulloch M DAHT25, 952715737, 115145929 Important Points, Operating Position, Stopping Your Engine, Starting Your Engine
Page 5 Page 7

115145929, 952715737, M DAHT25 specifications

The McCulloch 952715737 and 115145929 are ideal tools for homeowners and professionals alike, particularly in tasks that require a blend of efficiency and power. These models embody McCulloch’s commitment to quality and innovation in outdoor power equipment.

The McCulloch 952715737 is a robust chainsaw, designed for both occasional users and more seasoned professionals. Its lightweight construction enhances maneuverability, allowing users to tackle various tasks with ease—from simple branches to larger logs. One of the standout features is its powerful 2-stroke engine, which provides a substantial horsepower output, ensuring smooth operation even under heavy loads. The automatic oil pump delivers the right amount of lubrication to the chain and bar, optimizing performance while reducing wear and tear.

This chainsaw is equipped with a tool-less chain tensioning system that allows for quick adjustments without the need for additional tools. This feature is particularly valuable during extended use, where consistent tensioning is critical for safety and efficiency. The ergonomic handle, paired with anti-vibration technology, ensures user comfort, allowing for extended use without fatigue.

On the other hand, the McCulloch 115145929 model exemplifies versatility. This all-in-one tool is designed to cater to a variety of gardening and landscaping needs. It features an adjustable cutting head that can handle different tasks, from trimming hedges to edging lawns. The powerful engine ensures efficient cutting performance, while its lightweight design makes it easy to carry and maneuver.

Both models emphasize user-friendly technology, including an easy-start system that reduces the effort needed to start the machines, making them accessible even for novice users. Additional features in the 115145929 include multiple attachments that can be interchanged quickly, adding to its versatility across different gardening applications.

Overall, the McCulloch 952715737 and 115145929 models merge cutting-edge technology with user-oriented design, providing efficient and reliable solutions for outdoor maintenance. Whether you're a DIY landscaper or require a powerful tool for professional use, these models are tailored to meet diverse needs, ensuring exceptional results with every use.
Top Page Image Contents