Meets A.N.S.I. Safety Requirements | McCulloch MC624ES, 96192004000

OPERATION

MUFFLER

GASOLINE

FILLER CAP

CHOKE

CON-

TROL

SAFETY

IGNITION

KEY

ON / OFF

SWITCH

PRIMER

FUEL SHUT-OFF VALVE

RECOIL (AUXILIARY) STARTER HANDLE

	ELECTRIC	AUGER	DISCHARGE CHUTE CONTROL LEVER
	START	AUGER	DISCHARGE CHUTE CONTROL LEVER
	START	CONTROL
	BUTTON	CONTROL
	BUTTON	LEVER		TRACTION
		LEVER	DRIVE SPEED	TRACTION
	POWER		CONTROL LEVER	DRIVE
	POWER			CONTROL
		CORD		CONTROL
		CORD		LEVER
		PLUG		LEVER
		PLUG
		CHUTE
		DEFLECTOR

DISCHARGE

CHUTE

CHUTE

DEFLECTOR

KNOB

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT.

AUGERS

CLEAN-OUT TOOL

FIG. 8

HANDLE

KNOB

MUFFLER

TOOLBOX

SKID PLATE

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button – used for starting the engine.

Recoil (auxiliary) starter handle – used for starting the engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

ON / OFF switch - used to STOP the engine.

Choke control - used for starting a cold engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-pro- pelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the di- rection the snow is thrown.

Skid plate - used to adjust height of scraper bar from the

8 ground.

Image 8

McCulloch MC624ES, 96192004000 Meets A.N.S.I. Safety Requirements, Electric start button used for starting the engine

Contents

MC624ES Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Electric start button used for starting the engine HOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine Speed Storage OtherFuel System Engine OIL Troubleshooting Exploded KEY Part Description Auger Housing Auger Assembly LHAuger Assembly RH Scrapper BAR Auger Bearing Bearing PlugSkid Plate LH Skid Plate RH Knob Black POP RivetWasher Plastic Washer LEVER/CABLE Rotator Assembly Cable Assembly AdjustableCable Assembly Heat Shield Rotator Head 196944X431 Panel Bracket LH 196943X431 Panel Bracket RH Handle GripLower Handle Pivot Support Weldment 424517X431 Control Lever LH 424516X431 Control Lever RH 426918X008 Impeller ROD ARM Interlock BailSpacer Retainer Impeller ROD Traction RODShifter ROD TOP Shifter ROD Bottom Console Panel Interlock SpringInterlock CAM Torsion Spring Repair Parts Snow Thrower - Model Number MC624ES Drive Assembly Drive Plate AssemblySpeed Selector Rubber Ring Axle Shaft Roll PIN 3/16Sprocket Clik PIN Complete LCT Engine Frame427963X421 Engine Mounting Plate Electric Start Only Part Description Impeller Belt Traction BeltIdler ARM Bracket Idler Pulley 433666X421 Wheel Assembly LH433665X421 Safety Ignition KEY 422663 181037 DECAL, Danger Service Notes Service Notes Limited Warranty