To Remove Wheels See Fig, Carburetor | McCulloch 96192004000

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 21)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. To disengage drive system from the wheels (for pushing or transporting the snow thrower), remove klik pin from wheel hub and insert pin into the outermost hole in axle only.

KLIK PIN	OUTER HOLE
	INNER
	HOLE
WHEEL	WHEEL HUB

FIG. 21

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

TO ADJUST CABLE TENSION (See Fig. 22)

Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 22

17

Image 17

McCulloch 96192004000, MC624ES To Remove Wheels See Fig, Carburetor, Engine Speed, To Adjust Cable Tension See Fig

Contents

MC624ES Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Check Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Know Your Snow Thrower OperationPrimer Ignition KEY Electric start button used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See Fig To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Before Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigCarburetor Engine Speed Other StorageFuel System Engine OIL Troubleshooting Exploded KEY Part Description Auger Assembly LH Auger HousingAuger Assembly RH Scrapper BAR Bearing Plug Auger BearingSkid Plate LH Skid Plate RH POP Rivet Knob BlackWasher Plastic Washer Cable Assembly Adjustable LEVER/CABLE Rotator AssemblyCable Assembly Heat Shield Rotator Head Handle Grip 196944X431 Panel Bracket LH 196943X431 Panel Bracket RHLower Handle Pivot Support Weldment 426918X008 Impeller ROD ARM Interlock Bail 424517X431 Control Lever LH 424516X431 Control Lever RHSpacer Retainer Traction ROD Impeller RODShifter ROD TOP Shifter ROD Bottom Interlock Spring Console PanelInterlock CAM Torsion Spring Repair Parts Snow Thrower - Model Number MC624ES Drive Drive Plate Assembly AssemblySpeed Selector Rubber Ring Roll PIN 3/16 Axle ShaftSprocket Clik PIN Frame Complete LCT Engine427963X421 Engine Mounting Plate Electric Start Only Part Description Traction Belt Impeller BeltIdler ARM Bracket Idler Pulley 433666X421 Wheel Assembly LH433665X421 422663 Safety Ignition KEY DECAL, Danger 181037 Service Notes Service Notes Limited Warranty