Installation
|
|
|
| A custom cabinet installation should provide the follow- | ||||||||||
Installation |
|
|
| |||||||||||
The MC352 can be placed upright on a table or shelf, | ing minimum spacing dimensions for cool operation. Allow | |||||||||||||
at least 6 inches (15.24 cm) above the top, 2 inches | ||||||||||||||
standing on its four feet. It also can be custom installed in a | ||||||||||||||
(3.81cm) below the bottom and 1 inch (2.54 cm) on each | ||||||||||||||
piece of furniture or cabinet of your choice. The required | ||||||||||||||
side of the amplifier, so that airflow is not obstructed. Al- | ||||||||||||||
panel cutout, ventilation cutout and unit dimensions are | ||||||||||||||
low 21 inches (53.3 cm) depth behind the mounting panel, | ||||||||||||||
shown. |
|
|
| |||||||||||
|
|
| which includes clearance for connectors. Allow | |||||||||||
Always provide adequate ventilation for your MC352. | ||||||||||||||
inches (2.9 cm) in front of the mounting panel for knob | ||||||||||||||
Cool operation ensures the longest possible operating life | ||||||||||||||
clearance. Be sure to cut out a ventilation hole in the | ||||||||||||||
for any electronic instrument. Do not install the MC352 | ||||||||||||||
mounting shelf according to the dimensions in the drawing. | ||||||||||||||
directly above a heat generating component such as a high | ||||||||||||||
NOTE: In Europe, if the MC352 is custom mounted, an | ||||||||||||||
powered amplifier. If all the components are installed in a | ||||||||||||||
| additional ventilation opening of 6 inch (15.24 cm) in | |||||||||||||
single cabinet, a quiet running ventilation fan can be a defi- |
| |||||||||||||
| height, running the full width of the front panel, needs to | |||||||||||||
nite asset in maintaining all the system components at the |
| |||||||||||||
| be directly above the front top of the MC352. | |||||||||||||
coolest possible operating temperature. |
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| 444mm |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| 1/4" |
| 433.4mm |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| 6mm |
| Outline of Front Panel |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Front View of the MC352 |
|
|
|
|
|
|
| Edge of Cutout |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| 5.3mm | ||
|
|
|
|
|
|
|
|
|
|
|
|
| 7/32" | |
custom installed | End Caps |
|
| 212.7mm |
| (Front View) |
|
|
|
| ||||
225.8mm |
|
|
|
|
|
|
| |||||||
| 8.89" |
|
| Panel Height |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| 223.8mm |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3/16" |
|
|
| ||||
|
|
|
|
| 5.1mm |
|
| Support Shelf |
|
|
|
| Bottom of Cutout and Top |
|
| ||
|
|
|
|
|
|
| ||
|
|
|
| of Support Shelf Must |
|
|
| |
|
|
|
| Coincide |
|
|
| |
| Mounting Surface |
|
|
| ||||
|
|
|
|
|
|
| Mounting Bracket at Both Sides of the Rear Panel. | |
|
|
|
|
|
|
| ||
|
|
| See the note above |
| Fasten with | |||
|
|
|
|
|
|
| Fasten with 6 x 1/2 Wood Screw and Washer to Support Shelf | |
|
|
|
|
| Outline of Unit |
|
|
|
Side View of the MC352 |
|
|
|
|
|
|
|
|
|
|
|
| (Side View) |
|
|
| |
custom installed |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
Bottom View of the MC352 custom installed
Support Shelf | Cut Out Center |
| for Ventilation |
Mounting Surface
| Cut Out Center |
| for Ventilation |
| 15" |
6" | (Bottom View) |
| 9" |
5