How to Connect using a two Amplifiers

Caution: The AC Power Cord should not be connected to the Power Amplifiers until after the Loudspeaker Con- nections have been made. Failure to observe this could result in Electric Shock.

Follow the connection instructions below, together with the Connection Diagrams located on the separate folded sheet “Mc1A and 1B”, as this represents an example of a typical audio system. Your system may vary from this, however the actual components would be connected in a similar manner.

1.Prepare Loudspeaker cables by choosing one of the methods below:

Bare wire cable ends:

Carefully remove sufficient insulation from the cable ends, refer to figures 20, 21 & 22. If the cable is stranded, carefully twist the strands together as tightly as possible.

Figure 20

Figure 21

Figure 22

Note: If desired, the twisted ends can be tinned with solder to keep the strands together or attach spade lugs.

Spade lug or prepared wire connection:

Insert the spade lug connector or prepared section of the cable end into the terminal side access hole, and tighten the terminal cap until the cable is firmly clamped into the terminal so the wires cannot slip out. Refer to figures 23, 24 & 25.

5.Connect a Loudspeaker cable from the XCS2K MID Frequency INPUTS 2 (+) Binding Post to the (8 ohm) Binding Post B of the Power Amplifier number two.

6.Connect a Loudspeaker cable from the XCS2K MID Frequency INPUTS 3 (-) Binding Post to the (-) Bind- ing Post A of the Power Amplifier number two.

7.Connect a Loudspeaker cable from the XCS2K MID Frequency INPUTS 3 (+) Binding Post to the (8 ohm) Binding Post A of the Power Amplifier number two.

8.Connect Loudspeaker cables from the XCS2K LOW Frequency INPUTS 3 (-) and (+) Binding Posts to the (-) and (8 ohm) Binding Posts A of the Power Amplifier number one.

9.Connect Loudspeaker cables from the XCS2K LOW Frequency INPUTS 2 (-) and (+) Binding Posts to the (-) and (8 ohm) Binding Posts B of the Power Amplifier number one.

10.Connect Loudspeaker cables from the XCS2K LOW Frequency INPUTS 1 (-) and (+) Binding Posts to the (-) and (8 ohm) Binding Posts C of the Power Ampli- fier number one.

11.Tighten all of the Loudspeaker and Amplifier Binding Posts.

Figure 23

Figure 24

Figure 25

2.Connect a Loudspeaker cable from the XCS2K HIGH Frequency INPUTS 3 (-) Binding Post to the (-) Bind- ing Post C of the Power Amplifier number two.

Note: It is important to maintain the correct polarity at both ends of the Loudspeaker cables.

3.Connect a Loudspeaker cable from the XCS2K HIGH Frequency INPUTS 3 (+) Binding Post to the (8 ohm) Binding Post C of the Power Amplifier number two.

4.Connect a Loudspeaker cable from the XCS2K MID Frequency INPUTS 2 (-) Binding Post to the (-) Bind- ing Post B of the Power Amplifier number two.

14

Page 13 Page 15
Page 14
Image 14
McIntosh XCS2K owner manual How to Connect using a two Amplifiers
Page 13 Page 15

XCS2K specifications

The McIntosh XCS2K is a remarkable speaker system that epitomizes the brand's commitment to delivering premium audio experiences. As part of McIntosh's esteemed lineup of audio products, the XCS2K stands out with its sophisticated engineering and innovative technologies, designed to reproduce sound with unparalleled clarity and depth.

At the heart of the McIntosh XCS2K is its robust design, featuring a unique three-way configuration that allows for a well-balanced sound spectrum. This speaker incorporates dual 8-inch woofers, a premium 5.25-inch midrange driver, and a high-performance 1-inch tweeter. The combination of these specially crafted drivers ensures that the XCS2K can handle a wide range of frequencies, from deep bass to crystalline highs, making it ideal for various music genres and listening environments.

One of the standout features of the XCS2K is its proprietary Dynamic Power Management technology, which optimizes performance under varying load conditions. This technology ensures that the speakers maintain consistent sound quality, even at higher volumes, while minimizing distortion. Additionally, the speakers are designed to operate in conjunction with McIntosh amplifiers to achieve the best possible performance, showcasing the brand's commitment to synergy between components.

The XCS2K is also equipped with a remarkable array of connection options, allowing for seamless integration into any audio system. It features gold-plated binding posts for secure connections and is compatible with a range of amplifier configurations. The well-thought-out design also ensures that the speaker is aesthetically pleasing, featuring McIntosh's signature black glass front and iconic blue backlit logo, which adds a touch of elegance to any listening space.

Furthermore, the XCS2K supports advanced acoustic technologies, including adjustable bass and treble controls, allowing users to tailor the sound profile to their preferences. With its high sensitivity rating, the XCS2K can deliver impressive sound levels without requiring excessive power, making it a versatile option for both casual listeners and dedicated audiophiles.

Overall, the McIntosh XCS2K is a testament to the brand's legacy of excellence in audio engineering. With its premium components, advanced technologies, and striking design, it stands out as a powerful and versatile speaker system, ready to elevate your audio experience to new heights.
Top Page Image Contents