FX Loop Send / Return, Fx Mix, Recording | Mesa/Boogie DC3 specification

REAR PANEL: (Continued)

FX LOOP: SEND / RETURN:

These two 1/4" jacks are thae patch point for external effects. The Effects Loop is wired in parallel with the normal signal. Connect the SEND jack to your Effects Input jack. Connect the RETURN jack to the Output jack of your effect. The Effects Loop is a patch point between the pre-amp and power section. Therefore, the RETURN jack can double as a “Power

1.25A	RHY	Amp Input” jack.
1.25A	IN	LEAD
	OUT	FT SW

FUSE

EQ SELECT	SEND
2.5A SB
FTSW EQ/REV	RETURN

When the RETURN jack is used as an input, only the 5 Band EQ, the PRESENCE control of the active channel and the OUTPUT LEVEL control are being utilized, all other controls are inactive.

FX MIX:

This control determines the dry/wet blend of the FX Loop signal in relation to the unaffected signal. Set to 0% you will experience only the dry signal (no effect) and at a setting of 100% the entire signal will be wet (total effect.)

	IN	RHY
1.25A	IN	LEAD
	OUT	FT SW
FUSE		0%	10 0 %
		0%	10 0 %

EQ SELECT	SEND	FX MIX
2.5A SB
FTSW EQ/REV	RETURN	RECORDING

For the best results...Set the mix of your effect to 100% wet. Then dial in the amount of effect that you wish to hear, starting at 0% with the FX Loop Mix Control. The drier (closer to 0%) signal you use, the better your tone should be. This is one of the advantages in having a parallel type FX Loop designed into your DC-3amplifier...this circuit allows the amplifier to retain its purity with the least possible degredation due to effects impedance mismatching.

RECORDING:

This jack provides direct-to-console interfacing for recording or sound reinforcement applications. It is a circuit dedicated to reproduc- ing the roll off that occurs in the output section with a speaker connected. With accuracy, it faithfully captures the DC-3’ssoulful

character.

	IN	RHY
1.25A	IN	LEAD
	OUT	FT SW
FUSE				0%	10 0 %
				0%	10 0 %
2.5A SB	EQ SELECT		SEND		FX MIX
2.5A SB
	FTSW EQ/REV		RETURN	RECORDING

The send level strength is determined by the GAIN and MASTER Controls. From the Recording jack, adequate signal level will be available for most of your recording needs and live performances.

SILENT RECORDING:

This rocker switch which is located down under the chassis and selects between the live “Speaker On” setting and the silent “Speaker Mute” setting. This is a perfect solution for all-nighters! This switch mutes all of the signal at the power section driver s tage, removing

the need for a speaker load IN THIS POSITION ONLY!

0%	10 0 %
SEND	FX MIX

RETURN RECORDING

MUTESPKR ON

SILENT RECORDING

NOTE: When this switch is set to the “ON” position, a speaker load must be maintained by either a load resistor of some type or a speaker itself. Failure to comply with this instruction could result in major damage to the amplifier. Leave your speaker connected.

PAGE 8

DC3 specifications

The Mesa/Boogie DC-3 is a highly regarded guitar amplifier known for its versatility, power, and distinctive tone. Introduced during the early 1990s, the DC-3 has become a staple among musicians who appreciate its unique blend of classic and modern sounds. The amplifier is part of the Mark series, renowned for its innovative design and exceptional sound quality.

One of the standout features of the DC-3 is its all-tube preamp, which contributes to its warm and rich tonal characteristics. The amplifier utilizes three 12AX7 tubes in the preamp stage, providing a dynamic response that enhances the natural tonal qualities of the guitar. This all-tube configuration is complemented by a powerful 2x6L6 power tube setup, delivering a powerful 30 watts of output. This combination allows the DC-3 to produce a wide range of tones, from clean and sparkling to thick and saturated drive.

The DC-3 is equipped with a unique two-channel design, offering a Clean channel and a Lead channel, each with its own set of controls for ultimate tonal shaping. The Clean channel is characterized by its bright and articulate sound, making it suitable for a variety of genres, including jazz, pop, and rock. The Lead channel, on the other hand, offers greater gain and sustain, perfect for heavier styles like hard rock and metal. These channels can be blended together using the shared EQ, allowing for a truly customizable sonic experience.

Mesa/Boogie's innovative graphic equalizer further enhances the versatility of the DC-3. It features a five-band EQ that allows players to sculpt their sound with precision. This feature makes it easy to dial in the perfect tone for different performance environments, whether in the studio or on stage.

The DC-3 also includes a built-in reverb, adding depth and ambience to the overall sound. This is a valuable addition for musicians looking to enrich their performances without the need for additional effects pedals.

Robust construction and attention to detail are hallmarks of Mesa/Boogie amplifiers, and the DC-3 is no exception. It is built to withstand the rigors of touring and the demands of professional musicians. With its impressive tonal palette, reliable performance, and durable design, the Mesa/Boogie DC-3 continues to be a favorite among guitarists, making it a worthy investment for anyone serious about their craft.

Mesa/Boogie DC3 manual FX Loop Send / Return, Fx Mix, Silent Recording

Models: DC3