4. ELECTRICAL ENGINEERING
The electrical study for the implementation of a CleanWave→ filter is very easy. The few instructions described in this document must however be respected in order to ensure the safety and efficiency of the system.
4.1.ELECTRICAL SCHEMATIC
D1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CleanWave | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| L0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Z0 |
|
|
|
|
|
|
| Non | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| linear | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| load | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. 6
In order to minimise the disturbing currents in the installation, the CleanWave® filter should be placed close to the disturbing load.
4.2.ELECTRICAL PROTECTIONS
The CleanWave→ filter must be protected in a similar way as a transformer.
As a standard rule, the electrical protection D1 must be a tetrapolar circuit breaker ( 3 phases + neutral ) with neutral
If such a protection is not possible (e.g. when the neutral and earth connectors are common (PEN)), a tripolar breaker will be used and the PEN conductor section will be doubled, as recommended in table 4.
The breakers must be selected according to the phase current as given in table 4 here above. The maximum inrush current is lower or equal to the nominal current and doesn't require particular precautions.
4.3.WIRING
The minimum recommended wiring sections for the different connectors are given in table 4. These are minimum recommendations according to the European regulations. Higher sections may be used according to local regulations, particularities of the electrical installation or specific rules.
The neutral conductor may be crossed by a current up to 1.8 times the phase current and is therefore
MGE UPS SYSTEMS | CleanWave - Installation and user manual | Page 8/13 |
| Version 2.1.4 – 15/01/2007 - |
|
