Milwaukee 9071-20 manual Tool Assembly, Attaching and Removing Accessories Cat. No -20, 9072- 20

TOOL ASSEMBLY

WARNING

To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifi- cally recommended accessories. Others may be hazardous.

Removing and Replacing Quik-Lok®Cords (Fig. 1) Cat. No. 9072-20, 9072-22, 9092-20 and 9096-20

MILWAUKEE's exclusive Quik-Lok®Cords provide instant field replacement or substitution.

Fig. 3

Drive shank

Fig. 1

1.To remove the Quik-Lok®Cord, turn the cord nut 1/4 turn to the left and pull it out.

2.To replace the Quik-Lok®Cord, align the connector keyways and push the connector in as far as it will go. Turn the cord nut 1/4 turn to the right to lock.

Attaching and Removing the Tool Hanger (Fig. 2) Cat. No. 9092-20, 9096-20, or as an accessory

Fig. 2	Ring
Gear case	Tool
screws
	hanger

1.To attach, remove the two top gear case screws (Fig. 2).

2.Place the ring through the tool hanger.

3.Position the tool hanger on the tool over the two gear case screw holes.

4.Replace the two gear case screws. Hand tighten the screws.

5.To remove, reverse the procedure.

WARNING

Use only sockets and other accessories specifically designed for use on impact wrenches and drivers. Other sockets and acces- sories might shatter or break causing injury.

Attaching and Removing Accessories (Fig. 3) Cat. No. 9071-20, 9075-20

This impact wrench is intended only for use with sockets designed for impact wrenches and that have a 1/2" square drive (3/4" square drive for Cat. No. 9075-20). Other sockets could shatter or break, causing injury.

1.To attach a socket or other accessory, push the accessory onto the drive shank until it snaps into place.

2.To remove the accessory, pull it off the drive shank.

Attaching and Removing Accessories (Fig. 4) Cat. No. 9070-20, 9072- 20, 9072-22

These impact wrenches are intended only for use with sockets designed for impact wrenches and that have a 1/2" square drive. Other sockets could shatter or break, causing injury.

Fig. 4

Drive shank

Detent pin

1.To attach a socket or other accessory, align the hole in the accessory with the detent pin on the drive shank. Hold the detent pin in while pushing the socket onto the drive shank. The detent pin will snap into place in the hole to secure the socket.

2.To remove the accessory, insert a nail or other thin object into the hole in the accessory and press the detent pin in. Pull the accessory off the drive shank.

Attaching and Removing Accessories (Fig. 5) Cat. No. 9092-20, 9096-20, or other Impact Wrenches using the Quick Change 1/2" Square Drive to 7/16" Hex Adapter

Cat. No. 9092-20 and accessory Cat. No. 48-66-0061 are intended for use with drill bits and adapters with a 7/16" Hex Quick Change shank. Cat. No. 9096-20 is intended for use with drill bits and adapters with a 5/8" Hex Quick Change shank. Both Hex Quick Change shanks have a ball-retainer groove. They are not intended for use with Hex Shank Bit Extensions.

Fig. 5

Open (Release)

Ball-retainer groove

Closed (Locked)

1.To attach an accessory, pull the chuck collar forward and insert the ac- cessory shank. Release the collar. It may be necessary to pull the bit out slightly to engage the holding mechanism.

2.To remove the accessory, pull the chuck collar forward and remove the accessory. Release the collar.

page 5