Connecting the MS-10 Subwoofer
A/V Processor Connections
Your subwoofer has been designed for optimum performance with a Digital processor. If your AV processor has a line level or LFE subwoofer output you should use this connection. You will need to purchase a single screened RCA phono lead from your dealer. Connect this lead to the LFE/R input of the Subwoofer as shown.
Alternatively, you may use a split mono lead from the processor to both inputs of the subwoofer. In this case the input level at the subwoofer will be slightly higher.
Stereo Line Output Connections
If your amplifier has a spare preamplifier output or a stereo sub- woofer output, connect the
Pre Out - Main In Connections
If you use a stereo pre and power amplifier, or a stereo amplifier where the pre and main amplifier can be separated, connect the
Remove the
Speaker Level Connections
The high level Speaker connections should be used only if your amplifier does not have a line level subwoofer output. In this connection the subwoofer is fed together with the Front loudspeakers. For this you will need two extra twin core cables.
AV AMPLIFIER
RIGHT LEFT | RIGHT LEFT |
REAR CENTRE FRONT
Subwoofer Out (Line Level)
RIGHT LEFT | RIGHT LEFT |
REAR CENTRE FRONT
AV AMPLIFIER
L
R RIGHT LEFT | RIGHT LEFT |
REAR CENTRE FRONT
Stereo Outputs (Line Level)
(x2)
PRE MAIN
OUT IN
L 
AMPLIFIER
R 
RIGHT LEFT
TO FRONT
SPEAKERS
AMPLIFIER
The Mission MS-8 and MS-CUBE Powered Subwoofers
b | b | LINE LEVEL |
|
|
|
INPUT OUTPUT | CROSSOVER |
| |||
c | c | VOLUME FREQUENCY |
| ||
| 55Hz | 65Hz | PHASE | ||
LEFT | 45Hz | 75Hz | |||
|
|
| 0° | 180° | |
|
|
| 35Hz | ||
| d |
| 85Hz |
| |
d | RIGHT |
|
|
| |
| e |
| ON | OFF | |
e |
| 0 10 |
| AUTO | |
| POWER | ||||
|
|
|
| ||
|
| SPEAKER LEVEL INPUTS |
|
| |
f | f |
|
| ||
|
| ||||
|
|
| Active Subwoofer | ||
|
| R | L |
|
|
|
|
|
| N21090 | |
g | g |
|
|
|
|
h | h |
|
|
|
|
i | i |
|
|
j | j |
| WARNING: |
1) | 1) | TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, | |
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE | |||
|
| Serial Number |
|
|
|
| Power Inlet |
|
|
| Power |
1! | 1! |
|
|
|
| FUSE T3.15AL250V | OFF ON |
|
|
| |
|
| ||
|
| CAUTION: | ATTENTION: |
|
| DISCONNECT SUPPLY CORD | REPLACER LE FUSIBLE. |
|
| BEFORE CHANGING FUSE. | UTILISER UN FUSIBLE DE |
|
| REPLACE ONLY WITH SAME | RECHANGE DE MEME TYPE |
|
| TYPE FUSE AND RATING | ET CALIBRE |
NUMERICAL KEY | g Crossover Frequency Control | ||
b Phase Control | h Auto Power Switch |
| |
c Line Level Outputs | i Mains Power Indicator |
| |
d Line Level Inputs | j Mains ON/OFF Switch |
| |
e Volume Control | 1) IEC Mains Input Socket |
| |
f Speaker Level Inputs | 1! Mains Power Fuse |
| |
Measure out two loudspeaker cables of the appropriate length.
Prepare the cables as shown.
Connect the Left Speaker Terminals on the subwoofer to the Front Left speaker terminals on the amplifier. Connect the Red (+) speaker terminal on the amplifier to the Red (+) terminal on the subwoofer. Connect the Black
| SUBWOOFER |
SPEAKER LEVEL INPUTS | |
R | L |
Preliminaries
Open the carton and remove all the top packing pieces. Lift the subwoofer out carefully. DO NOT lift the subwoofer out of the carton using the protective bag. The unit is heavy; if you cannot
manage it easily, get assistance.
Retain the packing materials. If you decide not to keep the packing, please dispose of it having regard to any recycling regulations in your area. Please retain the user manual. If you transfer this equipment to a third party, please ensure all the instructions are passed on with the product.
Attaching Spikes (MS-CUBE)
Spikes may be fitted if required. To fit the spikes, follow the instructions for the
Power Connections
The subwoofer is factory set to operate from the mains voltage marked on the amplifier panel. Before connecting check this voltage is correct for your mains supply.
230 volt products - 220 V to 240 V
115 volt products - 110 Vs to 120 V
If you move to an area with a different mains supply, consult your dealer for advice.
10 | 7 | 6 | 7 |
