Mission MS-10 Specifications Welcome to Mission, General Information, Unpacking Your Loudspeakers

Specifications

Welcome to Mission

Recommended Amplifier:

Enclosure:

Effective Volume:

Frequency Response :

Filter Selection

Bass Unit

Net Weight

Dimensions (H x W x D): mm

Height on Feet mm

Electrical Class

MS-8

Integrated 100W amplifier

reflex

20 litres

38 Hz - 120 Hz

35Hz-85Hz (10 Hz steps)

250mm

11.0 kg

300 x 300 x 330

330

Class II

Do not Earth.

MS-10

Integrated 150W amplifier

reflex

35 litres

30 Hz - 165 Hz

40Hz - 200Hz (variable)

250mm

18.6 kg

410 x 280 x 500

410

Class I1 Requires Earth

MS-CUBE

Integrated 200W amplifier

reflex

30 litres

35 Hz - 110 Hz

35Hz-85Hz (10 Hz steps)

250mm

15.0 kg

380 x 345 x 370

380

Class I Requires Earth

MS-DUO

Integrated 150W amplifier

reflex

30 litres

35 Hz - 110 Hz

35Hz-85Hz (10 Hz steps)

250mm

15.2 kg

380 x 330 x 355

380

Class I Requires Earth

The Mv series is the latest in a long line of distinguished Mission loudspeakers. These technologically advanced loudspeakers will complement the finest electronics and décor. Robust bass drivers and precision silk tweeters are used throughout the range. Screw fastening tri-lobemulti-waybinding posts feature on all models. Your Mission Mv loudspeakers will bring you great listening pleasure for many years.

General Information

Please read these instructions carefully before installing your loudspeakers. A few minutes studying this manual will ensure superb performance from your loudspeaker for many years.

Please pay attention to all cautions printed on the pages marked with this symbol.

Unpacking Your Loudspeakers

•Carefully unpack each loudspeaker.

•Retain all the packing materials so that your loudspeaker can be repacked and shipped without damage.

•If you dispose of the packing,do so with regard to all recycling provisions in your area..

Mission reserves the right to change all specifications without notice. E & OE

Note for UK Customers

The power cord on your subwoofer may be supplied with a plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA or BSI approved BS1362 fuse must be used of the same rating. If the plug is cut off it must NOT be re-used. Dispose of any such plug safely. There is a danger of electric shock if a cut-off plug is inserted into a mains socket.

The wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth: Blue - Neutral: Brown - Live.

As the colours of the wires in the mains lead may not correspond with the markings identifying the terminals in the replacement mains plug, proceed as follows:

MS-DUO; MS-10: MS-CUBE:		EARTH (GREEN/YELLOW)
The wire coloured Blue must be connected to the
terminal marked with the letter ‘N’ or coloured Black.			FUSE
The wire coloured Brown must be connected to the
terminal marked with the letter ‘L’ or coloured Red.
The wire coloured Green and Yellow must be
connected to the terminal marked with the letter ‘E’,or		NEUTRAL	LIVE
coloured Green, or Green and Yellow, or marked with		(BLUE)	(BROWN)
the Earth symbol
MS-8:
			FUSE
The wire coloured Blue must be connected to the
terminal marked with the letter ‘N’ or coloured Black.
The wire coloured Brown must be connected to the
terminal marked with the letter ‘L’ or coloured Red	NEUTRAL		LIVE
		(BLUE)	(BROWN)

Fitting Spikes

Warning: Be careful. Loudspeaker spikes are very sharp.

When positioning the speakers avoid piercing any electrical cables.

•The Mv-6and Mv-8loudspeakers are supplied with the spike retainers fitted to the plinth but you will need to fit the spikes

Fitting the Spikes

•Invert the loudspeaker and place the top on a soft stable surface, or place the loudspeakers on a towel or soft cloth to protect the surface.

•Screw a nut fully on to each spike but ensure the nut is not tight.

•Place a washer over the spike retainer.

•Screw a spike half way into each spike retainer fitted in the base of the cabinet.

•Tighten the nut finger tight onto the spike retainer.

•Carefully return the loudspeaker to its normal position.

•Ensure that spikes do not pierce cables etc. under the carpet.

Adjusting the Spikes

•Loosen each collar slightly.

•Adjust the height by screwing in or out one or more of the spikes until the loudspeaker is stable and level.

•Tighten the nut fully tight onto the spike retainer.

Warning: The Mv-6and Mv-8loudspeakers are heavy.

Always get someone to help you to lift and manoeuvre the loudspeakers.

Never drag a loudspeaker. When moving loudspeakers lift them clear of the floor and replace them carefully

14 11 3