Mitsubishi Electronics 2.5KKC, PLH-2 Automatic cooling / heating, Selecting a temperature

Models: PLH-2 2.5KKC

1 20
Download 20 pages 29.78 Kb
Page 10
Image 10

E

4. Operation

 

 

 

 

 

 

4.6. Automatic (cooling / heating)

 

 

 

 

 

The AUTO mode starts with cooling or heating depending on the current

 

 

 

 

 

room temperature, higher or lower, than a selected temperature value

 

 

 

 

 

accordingly.

 

 

 

 

 

 

 

1 If the unit is off, press the ON/OFF button to turn it on.

 

 

 

 

 

A The ON indicator should light up.

 

 

 

 

 

 

2 Press the operation mode

button to select the

 

 

 

ON/OFF –

A

automatic mode .

 

 

 

 

 

B

should be displayed.

 

CENTRALLY CONTROLLED

 

 

 

 

1Hr.

 

 

3 If necessary, press

TEMP. button to set the desired temperature.

CHECK

ON OFF

˚C

FILTER

 

CLOCK

1

B

 

 

CHECK MODE

See page 10 for details.

 

STAND BY

˚C

 

TEST RUN

 

4 If necessary, press

button to select a desired rate.

 

 

 

DEFROST

NOT AVAILABLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See page 13 for details.

 

 

 

CLOCKON OFF

 

5 If necessary, press

to specify the vertical angle at which the

 

 

 

air is blowing.

 

 

 

 

FILTER

 

2

 

 

 

See page 14 for details.

 

 

 

CHECK

6 If necessary, press

button to set the timer.

 

 

 

 

3

TEMP.

TIMER SET

TEST RUN

See page 11 for details.

 

 

 

REMOTE CONTROLLER

 

 

 

 

 

PAR-JH240KA

 

 

 

 

 

6

4 5

 

 

 

 

 

 

 

4.7.

Selecting a temperature

TEMP.

 

 

 

 

 

s To decrease the room temperature:

 

 

 

 

 

 

1

Press

TEMP.

button to set the desired temperature.

A

 

 

 

 

A The selected temperature is displayed.

 

 

 

 

Each time you press the button, the temperature value decreases by

 

 

 

 

 

 

 

 

 

 

 

1°C.

 

 

 

 

 

 

 

 

 

ON/OFF –

s To increase the room temperature:

 

 

 

 

 

 

Press

 

button to set the desired temperature.

CENTRALLY CONTROLLED

1Hr.

 

1

TEMP.

 

 

A The selected temperature is displayed.

 

CHECK

 

ON OFF

˚C

FILTER

 

 

 

CLOCK

 

 

 

 

 

 

 

 

 

 

 

 

 

CHECK MODE

Each time you press the button, the temperature value increases by

 

˚C

 

 

TEST RUN

STAND BY

 

 

 

1°C.

 

 

 

 

 

DEFROST

 

NOT AVAILABLE

 

 

 

 

 

 

 

 

 

 

 

 

Available temperature ranges are as follows:

 

 

 

CLOCKON OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

FILTER

 

Cooling & Drying:

19 - 30°C

 

 

 

 

 

 

 

 

 

 

 

 

CHECK

 

Heating:

 

17 - 28°C

 

 

 

 

 

 

Automatic:

 

19 - 28°C

 

 

 

 

 

 

 

 

 

1

TEMP.

TIMER SET

 

TEST RUN

 

Circulation:

 

— (Not available)

 

 

 

 

 

 

 

 

 

REMOTE CONTROLLER

 

 

 

 

 

 

 

 

 

 

 

PAR-JH240KA

 

 

 

 

 

 

 

 

 

 

 

10

Page 10
Image 10
Mitsubishi Electronics 2.5KKC, PLH-2 operation manual Automatic cooling / heating, Selecting a temperature