Mitsubishi Electronics EX100U user manual Lamp replacement, Interval of lamp replacement

Lamp replacement

When the lamp no longer functions, replace it with a new one.

Caution:

•Do not remove the lamp immediately after using the projector. You may get burned because the lamp is very hot after use.

•Before replacing the lamp, press the POWER button to turn off the lamp and wait for two minutes for the lamp to cool down. Unplug the power cord from the wall outlet and wait one hour for the lamp to cool down completely.

•Do not remove the lamp except for replacement. Careless handling can cause injury or fire.

•Do not touch the lamp directly. It may break and cause injury or burn.

•Be sure not to drop the lamp lid screw into the projector. Also be sure not to put metal or any flammable objects inside because it may cause fire or electric shock. If any objects should fall inside, unplug and contact your dealer.

•Install the lamp securely to prevent failure and fire.

•If the lamp should break, small glass fragments may fall out through the grilles and some may remain inside of the projector or the lamp box. When taking the lamp box out, be sure to turn over the projector and hold the handle of the lamp box to avoid injury due to the glass fragments.

•If the lamp should break, never shake the lamp box or hold it in front of your face after removing it. The glass fragments may fall out and cause injury to your eyes.

•When placing the projector upside down to replace the lamp or conduct maintenance, ensure that the projector is securely placed before working with it.

1. Reverse the projector gently.

2. Loosen the screw (a) using a Phillips screwdriver (+), and remove the lamp cover (b).

3. Loosen the screws (c) using a Phillips screwdriver (+).

(b)(a)

4. Pull up the handle.

5.Pull out the lamp box by the handle while holding the projector.

• Pull the lamp box out of the projector slowly. If it is pulled

out quickly, the lamp may break	(c)
scattering glass fragments.
• Do not spill liquid on the removed
lamp box or do not place it near
any flammable object or where
children can reach to prevent
injury or fire.

6. Load a new lamp box securely into the projector in the right orientation.

7. Put the handle back to the original posi- tion.

• Make sure that the handle is locked.

8. Tighten up the screws (c) using a Phillips screwdriver (+).

9. Tighten up the screw (a) using a	(c)
Phillips screwdriver (+) to secure
the lamp cover.
Reset of the lamp operation time
Plug in the power cord, turn on the

lamp, and reset the lamp operation time by keep press- ing the ￿, ￿, and POWER buttons on the control panel at the same time about three seconds.

Important:

•Unless these three buttons are pressed at the same time, the lamp operation time isn't reset.

•Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.

•The projector doesn't turn on if the lamp cover isn't attached securely.

•Be sure to reset the lamp operation time whenever you replace the lamp.

•Do not reset the lamp operation time unless you replace the lamp.

Caution:

•The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.

•Contact your dealer for a new lamp.

Interval of lamp replacement

The recommended interval of lamp replacement is about 3000 - 5000 hours of consecutive use. Such interval differs depending on the operating environment and may be shorter. Decrease in luminescence and/or color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds the time elapsed until the lamp shutdown notice*1 is is- sued, the indicator will blink alternately green and red while the lamp is lit (while the lamp is not lit, the indica- tor will blink red only) and the lamp replacement mes- sage will appear on the screen for one minute every time the lamp is turned on. When the lamp operation time exceeds the time elapsed until the lamp shutdown warning*2 is issued, the replacement message (LAMP EXCHANGE) will appear on the screen for one minute at fixed intervals*4 thereafter.

When the lamp operation time exceeds the time elapsed until the lamp shutdown*3, the projector auto- matically shuts off and can't be used until the lamp is replaced and the lamp operation time is reset.

	EX100U		ES100U
*1	2250	Hours	3750	Hours
*2	2850	Hours	4750	Hours
*3	3000	Hours*5	5000	Hours*5

The times above are when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be shortened.

*4 These intervals vary depending on the lamp mode setting.

*5 When LAMP MODE is set to STANDARD, the time elapsed until the lamp shutdown will be shortened to 2000 hours.

Caution:

•This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental consider- ations. For disposal or recycling information, please contact your local authorities or the Electronic Indus- tries Alliance: www.eiae.org. (For US only).

EN - 22