Manuals
/
Brands
/
Computer Equipment
/
Computer Hardware
/
Mitsubishi Electronics
/
Computer Equipment
/
Computer Hardware
Mitsubishi Electronics
F940, F940GOT-LWD-E, F940GOT-SWD-E manual
- page 9
1
9
112
112
Download
112 pages, 1.95 Mb
INTRODUCTION 1.
1-1
1. INTRODUCTION
This section describes the product configuration and the system configurati
on of the graphic
operation terminal.
Confirm various functions of each unit.
F940GOT
-SWD-E/LWD-E
Contents
Main
Page
Page
F940GOT-SWD-E/LWD-E
Guidelines for the safety of the user and protection of the F940GOT-SWD-E/LWD-E
F940GOT-SWD-E/LWD-E
Page
Page
Page
Page
1.1 Outline of product
Page
Page
Page
Page
Page
1.2 Product configuration
Page
Page
Page
Page
Page
1-14
1.3 System configuration
When the GOT is directly connected to the PLC
PC
The system configuration to use the GOT is described below.
1-15
Peripheral units for GOT
1-16
The figure below shows connection to peripheral units used to create sequence programs.
PC
When built-in two-port interface function is used
Page
1-18
When the two-port interface FX-2PIF is use d
Page
Page
2. Installation, Wiring and General Specifications
2.1 Installation of main body
Page
Page
2.2 Wiring of power supply
Page
Page
Specifications of power supply unit
Page
2.3 Functions of operation keys and connectors
Page
Page
2.4 Outside dimensions
2.5 General specificationsl
Page
2.6 Connection to personal computer
2-16
Pin assignment and connection diagram of transfer cables - Transfer cable FX-232CAB-1
- Transfer cable FX-232CAB-2
2-17
- Transfer cable F2-232CAB-1
2-18
2.7 CPU port connection
POWER
RUN
1) 2)
a) b)
Page
2-20
- Connection cable FX-50DU-CAB0 (L, -1M, -10M, -20M, -30M)
Page
Page
Page
Page
Page
2.8 Computer link port connection (MELSEC A Series)
2-27
Connect the GOT to the computer link unit (PLC) as shown below. < For RS-422 communication >
< For RS-232C communication > The connection cable F2-232CAB is also available.
2-28
< For RS-232C communication >
2.9 Connection to SYSMAC C Series
2-30
< For RS-232C communication > Example of connection to C200H-LK201-V1
2-31
< For RS-232C communication > Example of connection to CQM1 (in which RS-232C port is built in)
2.10 Connection to FLEX-PC N Series
Page
2-34
< For link port connection (RS-232C) >
< For connection of built-in RS-232C interface >
2.11 Connection by general-purpose communication
Page
2-37
Connection diagram Connect the GOT and the host unit as shown below.
* The control lines RTS, CTS, DTR and DSR are not used.
Page
Page
3.1 Startup procedure
Page
F940GOT-SWD-E/LWD-E Startup 3.
3-4
F940GOT-SWD-E/LWD-E Startup 3.
3-5
3.2 Operation environment setting
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
4. Extension Module
4.1 Data transfer adaptor
Page
Page
Page
5. Maintenance
5.1 Outline of maintenance
Page
5.2 Replacement of battery
Page
5.3 Replacement of backlight
Page
6. Troubleshooting
6.1 Power indication
Page
Page
Page
7. Additional Functions (in Ver3.00 or later)
7.1 Applicable Versions and Models
Table 7.1 :
F940GOT-SWD-E/LWD-E Additional Functions (in Ver3.00 or later) 7.
7-2
7.2 Connection to MELSEC QnA Series PC
7.3 Connection to SLC 500 Series
F940GOT-SWD-E/LWD-E Additional Functions (in Ver3.00 or later) 7.
7-4
7.4 Connection to Bar Code Reader
Table 7.2 :Communication specifications
Table 7.3 :Data format
Page
7.5 Screen Hard Copy Function
7.6 Additional Function in Alarm History Display
7.7 Specification of Ten-Key Window Initial Display Position
Table 7.4:
8. Additional Functions (in V3.10 or later)
8.1 Applicable Versions and Models
Page
9. Additional Functions (in V4.00 or later)
9.1 Applicable Versions and Models
