Manuals / Brands / Power Tools / Welding System / Mitsubishi Electronics / Power Tools / Welding System

Mitsubishi Electronics FX1S 3.4 PLC Mounting Arrangements , Caution

1 68

Download 68 pages, 532.34 Kb

FX1S Series Programmable Controllers Installation Notes 3

3-5

3.4 PLC Mounting Arrangements

To prevent a rise in temperature, mount the units to walls. Never mount them to the floor or

ceiling of an enclosure.

Caution

• Units should mot be installed in areas subject to the following conditions: excessive or

conductive dust, corrosive or flammable gas, moisture or rain, excessive heat, regular

impact shocks or excessive vibration.

• Take special care not to allow debris to fall inside the unit during installation e.g. cut

wires, shavings etc. Once installation is complete remove the protective paper band: to

prevent overheating.

Figure 3.3: PLC Mounting Diagram

CPU

> 50mm(1.97 inches)

Contents

Main FX2NC Series Programmable Controllers Foreword Page Guidelines for the Safety of the User and Protection of the FX1S. Page Page Page Page Page Page Page Page 1-1 1. Introduction Table 1.1 : Relay Output Units Table 1.2 : Transistor Output Units Page 1.1 Model name Table 1.3 : Model Table FX1S-14MT-ESS/UL 1.2 World Specification 1.3 Serial Numbers Table 1.4 : World / Japanese Specifications Table 1.5 : Notes on Serial Numbers SERIAL NO.: 9 X 3267 1-5 1.4 Configuration Figure 1.2: Schematic system 1.4.1 Unit accessories Table 1.6 : Configuration Notes Table 1.7 : Connection Ports 1Memory Port 2Extension Board Port 3Programming Port 1.5 EEProm Backup Data Page Page Page FX1S Series Programmable Controllers Terminal layouts 2 2-1 Y4 2. Terminal layouts L -14MR-ES/UL -10MR-ES/UL -30MR-ES/UL 2.2 Transistor Output Controllers Figure 2.2: Terminal Layouts, Transistor Output -20MT-ESS/UL -30MT-ESS/UL -14MT-ESS/UL Page Page Page 3.1 Product Outline 3.2 FX1S RUN/STOP Control Figure 3.2: RUN/STOP Input Wiring Diagram n o 3.3 General Specifications Table 3.3: General Specifications 3.4 PLC Mounting Arrangements Caution Figure 3.3: PLC Mounting Diagram 3.5 DIN Rail Mounting 3.6 Termination of Screw Terminals Figure 3.4 : Terminal Crimp Diagram Page Page 4. Power Supply 4.1 Wiring Techniques 4.2 Wiring Cautions 4.3 Power Supply 4.4 Power Supply Characteristics *1 Includes the input current (5 or 7mA per point). Table 4.1 : Power Requirements Page Page Page Page 5. Inputs 5.1 24V DC Input Specifications Table 5.1: FX Input Specifications 5.1.1 Typical wiring Figure 5.1: Input Wiring Figure 5.2: Input Circuit Diagrams (Source/Sink) Figure 5.3: Diode Connection Diagram Figure 5.4: Parallel LED Diagram Rb Rp Rb Rp Page Page 6. Outputs Table 6.1: Output Specifications Page Figure 6.2: Dummy load Table 6.2: Relay Life Cycle Data Page Page Page Page Page 7. Diagnostics 7.1 Preliminary Checks 7.1.1 ERROR LED ON (CPU ERROR) 99 8 Page 7.4 Operation and Error Flags 7.5 Error Registers Page 7.6 Error Codes 7.7 Instruction List Table 7.1: Numerically sorted Table: 7.2 Alphabetically sorted Page FX1S Series Programmable Controllers Diagnostics 7 7.8 Device List FX1S Series Programmable Controllers Diagnostics 7 Page HARDWARE MANUAL