Mitsubishi Electronics FX1S 7. Diagnostics

FX1S Series Programmable Controllers Diagnostics 7

7-1

7. Diagnostics

7.1 Preliminary Checks

Check power supply, ground and I/O cables are wired correctly.

Turn the power supply on. Check the power LED is lit. Down load a small

test program into the PLC. Verify the program to ensure it has been written

to the PLC correctly. Using the programming device forcibly turn ON/OFF

each output. Check the output LEDs for operation.

Put the PLC into RUN. Check the RUN LED is lit. Check the previously down

loaded program works correctly. Onc e all chec ks a re complete tak e the PLC

out of run and turn OFF the power supply.

During this testing stage take extreme care not to touch any live or hazard-

ous parts.

POWER

RUN

ERROR

POWER

RUN

ERROR

POWER

RUN

ERROR

Contents

Main FX2NC Series Programmable Controllers Foreword Page Guidelines for the Safety of the User and Protection of the FX1S. Page Page Page Page Page Page Page Page 1-1 1. Introduction Table 1.1 : Relay Output Units Table 1.2 : Transistor Output Units Page 1.1 Model name Table 1.3 : Model Table FX1S-14MT-ESS/UL 1.2 World Specification 1.3 Serial Numbers Table 1.4 : World / Japanese Specifications Table 1.5 : Notes on Serial Numbers SERIAL NO.: 9 X 3267 1-5 1.4 Configuration Figure 1.2: Schematic system 1.4.1 Unit accessories Table 1.6 : Configuration Notes Table 1.7 : Connection Ports 1Memory Port 2Extension Board Port 3Programming Port 1.5 EEProm Backup Data Page Page Page FX1S Series Programmable Controllers Terminal layouts 2 2-1 Y4 2. Terminal layouts L -14MR-ES/UL -10MR-ES/UL -30MR-ES/UL 2.2 Transistor Output Controllers Figure 2.2: Terminal Layouts, Transistor Output -20MT-ESS/UL -30MT-ESS/UL -14MT-ESS/UL Page Page Page 3.1 Product Outline 3.2 FX1S RUN/STOP Control Figure 3.2: RUN/STOP Input Wiring Diagram n o 3.3 General Specifications Table 3.3: General Specifications 3.4 PLC Mounting Arrangements Caution Figure 3.3: PLC Mounting Diagram 3.5 DIN Rail Mounting 3.6 Termination of Screw Terminals Figure 3.4 : Terminal Crimp Diagram Page Page 4. Power Supply 4.1 Wiring Techniques 4.2 Wiring Cautions 4.3 Power Supply 4.4 Power Supply Characteristics *1 Includes the input current (5 or 7mA per point). Table 4.1 : Power Requirements Page Page Page Page 5. Inputs 5.1 24V DC Input Specifications Table 5.1: FX Input Specifications 5.1.1 Typical wiring Figure 5.1: Input Wiring Figure 5.2: Input Circuit Diagrams (Source/Sink) Figure 5.3: Diode Connection Diagram Figure 5.4: Parallel LED Diagram Rb Rp Rb Rp Page Page 6. Outputs Table 6.1: Output Specifications Page Figure 6.2: Dummy load Table 6.2: Relay Life Cycle Data Page Page Page Page Page 7. Diagnostics 7.1 Preliminary Checks 7.1.1 ERROR LED ON (CPU ERROR) 99 8 Page 7.4 Operation and Error Flags 7.5 Error Registers Page 7.6 Error Codes 7.7 Instruction List Table 7.1: Numerically sorted Table: 7.2 Alphabetically sorted Page FX1S Series Programmable Controllers Diagnostics 7 7.8 Device List FX1S Series Programmable Controllers Diagnostics 7 Page HARDWARE MANUAL