Mitsubishi Electronics FX3G

825

FX3G/FX3U/FX3UC Series Programmable Controllers

Programming Manual - Basic & Applied Instruction Edition

37 Operation of Special Devices (M8000 -, D8000 -)

37.1 Special Device List (M8000 -, D8000 -)

FNC275-FNC279

Data

Transfer 3

FNC280-FNC289

High Speed

Processing 2

FNC290-FNC299

Extension File

FNC300-FNC305

-CF-ADP

SFC•STL

Programming

Interrupt

Function

Special Device

Error Code

Version Up

Information

Execution Times

High Speed Counter Comparison, High Speed Table, and Positioning [Positioning is supported in FX3G, FX1S, FX1N, and FX1NC PLCs.]

M 8130 HSZ (FNC 55)instruction: Table comparison mode –3 3

D8130

––3–3

[M]8131 HSZ (FNC 55)instruction:

Table comparison mode completion flag –3 3 ––3–3

M 8132 HSZ (FNC 55) and PLSY (FNC 57) instructions: Speed

pattern mode –3 3 D8131 to

D8134

––3–3

[M]8133 HSZ (FNC 55) and PLSY (FNC 57) instructions: Speed

pattern mode completion flag –3 3 ––3–3

[M]8134

Not used

– – – – –––– –

[M]8135 – – – – –––– –

[M]8136 – – – – –––– –

[M]8137 – – – – –––– –

[M]8138 HSCT (FNC280) instruction:

Instruction execution complete flag –3 3 D8138 – – – – –

[M]8139

HSCS(FNC 53), HSCR(FNC 54), HSZ(FNC 55),

HSCT(FNC280) instructions:

High speed counter comparison instruction executing

–3 3 D8139 – – – – –

M 8140 ZRN (FNC156) instruction:

CLR signal output function enable – – ––33 –3–

[M]8141

Not used

– – – – –––– –

[M]8142 – – – – –––– –

[M]8143 – – – – –––– –

[M]8144 – – – – –––– –

M 8145 [Y000] Pulse output stop command 3–––33 –3–

M 8146 [Y001] Pulse output stop command 3–––33 –3–

[M]8147 [Y000] Pulse output monitor (BUSY/READY) 3–––33 –3–

[M]8148 [Y001] Pulse output monitor (BUSY/READY) 3–––33 –3–

[M]8149 Not used – – – – –––– –

Inverter Communication Function (Refer to Data Communication Edition for details.)

[M]8150 Not used – – – – –––– –

[M]8151*1 Inverter communication in execution [ch1] 3*3 3 3 D8151 – – – – –

[M]8152*1 Inverter communication error [ch1] 3*3 3 3 D8152 – – – – –

[M]8153*1 Inverter communication error latch [ch1] 3*3 3 3 D8153 – – – – –

[M]8154*1 IVBWR (FNC274) instruction error [ch1] –3 3 D8154 – – – – –

[M]8154 Defined per use of EXTR (FNC180) – – ––––

3*2 –3*2

[M]8155 EXTR (FNC180) is using communicating port – – – D8155 – – 3*2 –3*2

[M]8156*1 Inverter communication in execution [ch2] 3*3 3 3 D8156

[M]8156 Communication error or parameter error in EXTR

(FNC180) instruction – – – D8156 – – 3*2 –3*2

[M]8157*1

Inverter communication error [ch2] 3*3 3 3 D8157

Communication error in EXTR (FNC180) instruction is

latched. – – – D8157 – – 3*2 –3*2

[M]8158*1 Inverter communication error latch [ch2] 3*3 3 3 D8158 – – – – –

[M]8159*1 IVBWR (FNC274) instruction error [ch2] –3 3 D8159 – – – – –

*1. Cleared when PLC switches from STOP to RUN.

*2. Available in Ver. 3.00 or later.

*3. Available in Ver. 1.10 or later.

Number and name Operation and function

Applicable model

3G FX3U

3UC

Correspond-

ing special

device

1NC

2NC