Mitsubishi Electronics FX3G

826

FX3G/FX3U/FX3UC Series Programmable Controllers

Programming Manual - Basic & Applied Instruction Edition

37 Operation of Special Devices (M8000 -, D8000 -)

37.1 Special Device List (M8000 -, D8000 -)

Advanced Function

M 8160*1 SWAP function of XCH (FNC 17) –3 3 –––3–3

M 8161*1*2 8-bit process mode 3 3 3 –3333 3

M 8162 High speed parallel link mode 3 3 3 –3333 3

[M]8163 Not used – – – – –––– –

M 8164*1 FROM (FNC 78), TO (FNC 79) instructions:

Transfer points variable mode – – – D8164 – – 3*3 –3

M 8165*1 SORT2 (FNC149) instruction:

Sorting in descending order –33*4 – –––– –

[M]8166 Not used – – – – –––– –

M 8167*1 HKY (FNC 71) instruction:

HEX data handling function –3 3 –––3–3

M 8168*1 SMOV (FNC 13) instruction:

HEX data handling function 3 3 3 –––3–3

[M]8169 Not used – – – – –––– –

*1. Cleared when the PLC switches from RUN to STOP.

*2. Applicable to ASC (FNC 76), RS (FNC 80), ASCI (FNC 82), HEX (FNC 83), CCD (FNC 84), and CRC

(FNC188) instructions*5.

*3. Available in Ver. 2.00 or later.

*4. Available in Ver. 2.20 or later.

*5. CRC (FNC188) instruction is available only in FX3U and FX3UC PLCs.

Pulse Catch (Refer to Section 36.7 for details.)

M 8170*6 Input X000 pulse catch 3 3 3 –3333 3

M 8171*6 Input X001 pulse catch 3 3 3 –3333 3

M 8172*6 Input X002 pulse catch 3 3 3 –3333 3

M 8173*6 Input X003 pulse catch 3 3 3 –3333 3

M 8174*6 Input X004 pulse catch 3 3 3 –3333 3

M 8175*6 Input X005 pulse catch 3 3 3 –3333 3

M 8176*6 Input X006 pulse catch –3 3 – –––– –

M 8177*6 Input X007 pulse catch –3 3 – –––– –

*6. Cleared when PLC switches from STOP to RUN.

FX2N, FX2NC, FX3U, or FX3UC Series PLC: EI (FNC 04) instruction is necessary.

FX3G, FX1S, FX1N, or FX1NC Series PLC: EI (FNC 04) instruction is unnecessary.

Communication Port Channel Setting (Refer to Data Communication Edition for details.)

M 8178 Parallel link channel switch (OFF: ch1/ON: ch2) 3 3 3 – –––– –

M 8179 N:N network channel switch*7 3 3 3 – –––– –

*7. The channel is specified by either setting or not setting M8179 in the setting program.

→ For setting program, Refer to Data Communication Edition

• ch1: M8179 is not set in program

• ch2: M8179 is set in program

Number and name Operation and function

Applicable model

3G FX3U

3UC

Correspond-

ing special

device

1NC

2NC