Mitsubishi Electronics SL2U XL1X user manual Image, Installation

Menu operation (continued)

1IMAGE

CONTRAST ........ Adjusts the picture contrast. The contrast becomes higher as			opt.	XGA60
the number increases.
BRIGHTNESS .... Adjusts the image brightness. The image becomes brighter as	IMAGE
the number increases.		CONTRAST		0
sRGB ................... Select ON to display an image emphasizing on the color		BRIGHTNESS		0
reproducibility.		sRGB		OFF
• When sRGB is ON, COLOR MATRIX, COLOR TEMP.		COLOR MATRIX		COMPUTER
and GAMMA MODE can’t be adjusted.		COLOR TEMP.		STANDARD
COLOR MATRIX ... Adjusts the color balance in each color of the image. See page 18.		COLOR		0
COLOR TEMP. ... Adjusts the color temperature. See page 19.		TINT		0
COLOR ................ Adjusts the color intensity of the image. (Available only when		SHARPNESS		0
VIDEO is selected as the source.)		GAMMA MODE		AUTO

TINT .................... Adjusts the color balance of the image. The color balance of the image shifts green as the

number increases and shifts to purple as the number decreases. (Available only when VIDEO is selected as the source.)

•When the TV50 (PAL, SECAM) signal is inputted, TINT can’t be adjusted. SHARPNESS ...... Adjusts the image sharpness. The image sharpness rises as the number increases. GAMMA MODE ..... When AUTO is selected, the appropriate gamma mode is automatically selected depending

on the input signal. For normal use, select AUTO. Select DYNAMIC for computer sources. Select STANDARD for sport scenes and video sources. Select THEATER for projecting film sources.

2INSTALLATION

RIS ....................... Adjusts the sensitivity of the function (RIS) which				opt.	XGA60
automatically adjusts the brightness and contrast of the
	INSTALLATION
image depending on the degree of the light in the room. When
using this projector in a room where the light and shade			RIS		OFF
			KEYSTONE		0
varies slightly, select 1. When using this projector in a
			AUTO POWER		OFF
normally lighted room, select 2. When using this projector in			ON
			AUTO POWER		OFF
a room where the light and shade varies greatly, select			OFF
			SPLASH SCREEN		ON
3.When you select OFF, RIS won’t operate.		ON
• When the sensitivity is adjusted in a large amount, the			BACK COLOR		BLUE
image may be displayed solid white. Adjust the sensitiv-			MUTE MODE		BLACK
ity depending on the operating environment and imges to			LAMP MODE		STANDARD
			IMAGE REVERSE		OFF
be displayed.
KEYSTONE ........ Corrects keystone distortion. Select an optimum value for
proper display. For normal use, select 0.

AUTO POWER ON .... Select ON to boot up the projector automatically by turning on an externally connected

power switch such as a breaker even when the main power switch of the projector is off. Use this setting when the projector is hanging from the ceiling.

•The projector will be in the stand-by mode when the lamp is off. Use the remote control to turn on the lamp.

AUTO POWER OFF .. Set the time elapsed before the projector enters into the stand-by mode when there is no signal inputted from the selected source.

SPLASH SCREEN ..... Select ON to display the splash screen when the power is turned ON.

BACK COLOR .... Use to select the background, BLUE, LOGO or BLACK, which will be displayed when there

is no signal inputted from the selected source. When the LOGO is selected, the splash screen will be displayed.

MUTE MODE ..... Use to select the background, BLACK or LOGO, which will be displayed when the MUTE

button is pressed. When the LOGO is selected, the splash screen will be displayed.

LAMP MODE ...... Use to change the brightness of the lamp. When LOW is selected, the image will become

darker, though the power will be saved, operating sound will be reduced.

•The intensity of the lamp will be STANDARD for 3 minutes regardless of the setting of the LAMP MODE when the lamp turns on.

•When the LAMP MODE is changed, the screen may flicker. This is not a failure of the lamp.

IMAGE REVERSE ..... Use to reverse or invert the projected image. Select MIRROR in rear projection. Select

MIRROR, INVERT in rear projection with the projector hanging from the ceiling.

•When no signal is supplied for 6 hours with BACK COLOR set to BLACK, it changes to BLUE automatically for the purpose of protecting the projector.

•When you continue projection for a long time with BACK COLOR or MUTE set to LOGO, an after-image may persist on the screen.

•When the signal is lost during muting with MUTE set to LOGO, AUTO POWER OFF is ignored even though it is active.

EN – 16