POWERED SUBWOOFER

where the subwoofer sounds in balance with the satellite speakers. If the system is not working properly, unplug the subwoofer and check all of your connections. Call your dealer or the factory if you cannot solve any problem.

6.USE OF THE “PHASE” CONTROL

Your subwoofer has a phase control that allows for continuous adjustment between 0˚and 180˚ degrees. This con- trol let you fine tune the transition between the subwoofer and your other speakers.

To optimize the sound of your new subwoofer, you need to perform a Phase Test. This test insures optimum sound in the critical bass frequencies where your subwoofer and Satellite speakers overlap.

Play a familiar CD, LP, or tape with steady, consistent bass. Set the “PHASE” control to the 0˚ position. Listen care- fully to the mid-bass (70 - 100 Hz) region — the part of the spectrum where electric or string basses and drums are found. Then, adjust the "PHASE" control to the 180˚ position.

Now listen to the same musical passage, concentrating on the mid-bass region. If you hear less bass, the previous 0º position, would be the correct. If you hear more bass, the new 180˚ position is correct. If you have two subwoofers, perform one test for each subwoofer. When you perform each test, make sure the other subwoofer is not operating by switching it to the “OFF” position or unplugging the power cord.

Once you have established which position gives the most bass, you can further fine-tune the control to produce the best possible sound by adjusting it between 0˚ and 180˚. When you hear the best balance between stereo image local- ization and maximum impact and output in the midbass, you have found the correct setting.

If you hear little or no difference when you adjust the “PHASE” control knob, set it to the default 0˚ position.

Another method of setting phase uses a pink noise source and a spectrum analyzer. If you have these, place the microphone at the main listening position and look at its display in the mid-bass region of 70 - 100 Hz. The wiring/ switch position showing the most output in that region has the correct phase.

You need to perform this test because when satellite speakers are located separate from a subwoofer, each speak- er is at a different distance from your ear. In some cases, the difference will be just enough so that the output from the subwoofer arrives out of phase with the output of the satellites. When this happens, that critical mid-bass is actually can- celled. You should re-do this test any time you move your speakers

7.USE OF THE "LOW PASS FILTER" CONTROL

The back panel control "LOW PASS FILTER" sets the upper rolloff point of the subwoofer, eliminating mid-bass and midrange that are being reproduced by your satellite speakers. The control is a means of fine-tuning the transition between your subwoofer and satellite speakers, and it provides a rolloff of 12 dB/octave up to 200 Hz, where the filter shifts to 36 dB/octave. In most systems, including M&K satellites, 85 Hz gives the best blend. If you don't want to experiment, set the control at 85 Hz. If you are using the K-5 / K-7 Satellites, set the control to 100Hz. If you are using Xenon satellites (LCR45, LCR35, or LCR25), or the MP4512, set the control between 125 and 200 Hz.

The goal is to get a balanced acoustic output in your room. This is not necessarily the same as flat electrical out- put. Rooms typically reinforce bass frequencies around 100 Hz, so by leaving an electrical gap, you may actually get a smooth acoustical response where it matters, in the room.

Think of this control as a mid-bass fine tuning adjustment that you set to achieve the best transition between the satellite speakers and the subwoofer. When you hear a smooth sound overall, well balanced between the deep bass and the rest of the audible spectrum, the control is set properly.

8.USE OF THE "BYPASS" SETTING

If you have a THX, Dolby Digital, or DTS component with a built-in Low-Pass filter as part of its subwoofer output, or if you are using a separate Electronic Crossover, set the “LOW PASS FILTER” switch on the back of the subwoofer to “BYPASS” position. This bypasses the internal low-pass filter so that there is no interaction between the subwoofer’s filter and your component’s filter. If you have any questions regarding the filters, please contact your M&K dealer or the M&K factory.

9

Page 8 Page 10
Page 9
Image 9
MK Sound VX-860, VX-850 USE of the Phase Control, USE of the LOW Pass Filter Control, USE of the Bypass Setting
Page 8 Page 10

VX-860, VX-850 specifications

MK Sound is a renowned brand that has long been synonymous with high-quality audio equipment. Among their impressive lineup of speakers, the VX-860 and VX-850 stand out for their exceptional performance and innovative technologies. These models cater to audiophiles and home theater enthusiasts who crave unparalleled sound quality and immersive audio experiences.

The MK Sound VX-860 is designed with a 2-way configuration, featuring a 6.5-inch woofer and a 1-inch tweeter. This speaker is engineered to deliver a wide frequency response, allowing users to experience deep bass and crisp highs. The advanced woofer design utilizes a lightweight, rigid cone that enhances sound clarity and reduces distortion. The tweeter, with its soft dome design, contributes to a smooth and detailed high-frequency response, making it ideal for both music and movie soundtracks.

In contrast, the VX-850 offers a slightly smaller 5.25-inch woofer, coupled with a 1-inch tweeter. This model is perfect for compact spaces without compromising on sound quality. The VX-850 features similar design principles to its larger counterpart, ensuring that it provides articulate sound reproduction and impressively low distortion levels. Both models boast a frequency response range that vividly captures the nuances of audio, making them suitable for various listening environments.

Technologically, MK Sound incorporates several innovative features in these speakers. One of the standout attributes is the company’s exclusive “Time Domain” technology. This proprietary system enhances imaging and soundstage by aligning the speaker's acoustical performance with the human auditory system. As a result, users enjoy a more immersive and realistic listening experience, whether they are watching movies or enjoying their favorite tracks.

The cabinets of the VX-860 and VX-850 are constructed from high-quality materials, offering excellent durability while minimizing unwanted resonances. The speakers have been designed to integrate seamlessly with various home theater setups and can be easily paired with a wide array of amplifiers and AV receivers.

In conclusion, the MK Sound VX-860 and VX-850 speakers exemplify the brand's commitment to crafting superior audio equipment. With their advanced technologies, robust design, and outstanding sound quality, these models are ideal choices for anyone looking to elevate their listening experience. Whether for music, movies, or gaming, the VX-860 and VX-850 promise to deliver an extraordinary sonic experience that captivates the senses.
Top Page Image Contents