Lavatory Lift Rod and Waste Assembly
1.Thoroughly clean around drain opening in lavatory sink. Apply 1/4 inch bead of plumber's putty (not furnished) around the bot- tom side of seat.
2.Apply pipe joint compound or Teflon tape (not furnished) to top threaded end of the drain body. Slip drain body up through the drain opening and screw seat on the drain body.
3.Position the drain body with pivot rod opening extending rear- ward and tighten mounting nut until the drain body is snug. Wipe excess plumber's putty from the seat area. Apply pipe joint com- pound (not furnished) to top threaded end of tailpipe and screw into drain body. Tighten firmly by hand.
4.Position drain plug in either of the following ways:
A. VANDALPROOF - this design is to prevent unauthorized re- moval of the drain plug. Unscrew the pivot nut and remove the pivot rod. Inside the drain body position the pivot rod through the drain plug hole as shown in the illustration below. Screw the pivot nut back on the drain body. DO NOT OVERTIGHTEN.
A. VANDALPROOF
PIVOT | VANDALPROOF | |
ROD | ||
POSITION | ||
|
B.EASY REMOVAL - This design is for quick removal of drain plug for cleaning. Just drop in the drain plug as shown in the
illustration below.
POSITION FOR
EASY REMOVAL
PIVOT
ROD
5. Install lift rod, with knob attached, into top of spout as shown. Secure lift rod strap to bottom end of lift rod as shown. With pivot rod in the down position, assemble strap to pivot rod using the spring clip. The strap will have to be bent to reach the pivot rod on some installations. Adjustment may be required so lift rod clears spout tube and connection (i.e., bend spout tube out- wards).
6. With the drain plug in full open position, adjust lift rod and knob to clear faucet and tighten lift rod strap screw.
FAUCET PARTS | HANDLE |
SCREW | |
| HANDLE |
| KNOB |
| STEM |
| GUIDE |
| CARTRIDGE |
| NUT |
| STEM |
| EXTENSION |
| CARTRIDGE |
| ESCUTCHEON |
| MOUNTING NUT |
| MOUNTING |
| WASHER |
| MOUNTING |
| NUT |
CAUTION: To avoid the lift rod knob rubbing against spout, do not install rod any lower than
dimension shown.
LIFT ROD
AND KNOB
SPOUT 
| DRAIN |
|
|
|
|
| PLUG |
|
|
|
|
|
|
| VANDAL- |
|
|
|
|
| PROOF |
|
|
|
|
| HOLE |
| LIFT |
|
|
|
|
| ROD |
|
|
|
|
| STRAP |
|
|
|
|
| SCREW |
| SEAT | PIPE |
|
| |
|
|
| JOINT |
|
|
|
|
| COMPOUND |
|
|
|
|
| OR | LIFT |
|
|
|
| TEFLON |
| |
|
|
| ROD |
| |
|
|
| TAPE (NOT |
| |
| STRAP |
| |||
FURNISHED) |
| ||||
|
| ||||
|
|
|
| ||
|
|
|
|
| |
MAX. | MIN. |
|
|
|
|
|
|
| BOTTOM |
|
|
|
|
| GASKET |
|
|
MOUNTING |
| FLAT |
|
| |
| WASHER |
| |||
| NUT |
|
|
|
|
|
|
|
|
| SPRING |
| DRAIN |
|
|
| CLIP |
|
|
|
|
| |
| BODY |
|
|
|
|
8" |
|
|
|
|
|
| PIPE |
| PIVOT |
|
|
|
| NUT |
|
| |
| JOINT |
|
|
| |
|
|
|
|
| |
COMPOUND |
| PIVOT |
|
| |
| OR |
|
|
| |
|
| ROD SEAT |
|
| |
| TEFLON |
|
|
| |
|
|
|
| PIVOT | |
| TAPE (NOT |
| LIFT ROD | ||
|
| ROD | |||
FURNISHED) |
| ||||
|
| STRAP |
| ||
|
|
|
|
| |
|
|
| TAILPIECE | SHOWN |
|
|
|
|
| IN BENT |
|
|
|
|
| POSITION |
|
LIFT ROD
AND KNOB
FLOW RATOR
AERATOR
SPOUT
ASSEMBLY
SPOUT MOUNTING
WASHER
SPOUT
MOUNTING NUT
SPOUT
UNION TEE
WATER
SUPPLY LINE
