
How Your Humidifier Works
Your new humidifier is designed to satisfy home humidity requirements through the principle of evaporation of water in the air.
Once the filter becomes saturated, air is drawn in, passes through the filter and moisture is absorbed into the air. All evaporation occurs in the humidifier so any residue remains in the filter. This natural process of evaporation virtually eliminates white dust.
CAUTION: To reduce the risk of injury, fire or damage to humidifier, use only cleaners specifically recommended for humidifiers. Never use flammable, combustible or poisonous materials to clean your humidifier. To reduce the risk of scalds and damage to humidifier, never put hot water in humidifier.
Getting Your
Humidifier Up
and Running
Once removed from its carton, remove all packing materials. Verify the filter is properly installed (See page 10).
Step 1. Location
WARNING: For your own safety, do not use humidifier if any parts are damaged or missing.
Troubleshooting
Trouble |
| Probable Cause |
| Remedy | |
Digital display not | • | No Power | • | Check 120 volt power source. | |
| Power button has not been | • | Press power button once to turn | ||
illuminated. |
| ||||
| depressed. |
| on. | ||
|
|
| |||
| • | ROOM humidity level is not 3% or | • Raise SET humidity level if | ||
Fan not operating (digital |
| desired. | |||
| more below SET humidity level. |
| |||
display is illuminated). |
| • | Increase fan speed. | ||
• | Reservoir is empty. | ||||
| • Fill humidifier with water. | ||||
|
|
| |||
|
|
| • A Set humidity percentage of 65% | ||
| • SET humidity level is 65%. |
| operates fan continuously. Adjust | ||
Fan running | • | ROOM humidity level has not |
| SET level between | |
continuously. |
| reached 1% or more above SET | • | Continue to run until desired | |
|
| humidity level. |
| humidity level is achieved. This | |
|
|
|
| may take up to 48 hours initially. | |
|
|
|
|
| |
Poor evaporation of | • | CHECK FILTER message | • | Change to a fresh new filter. | |
| flashing. | • | NOTE: Local water purity varies | ||
water. |
| ||||
• Mineral buildup on filter. |
| from area to area. | |||
|
| ||||
Bottle empties | • | This is normal for | • Refill bottle for maximum run time. | ||
completely. |
| initial filling. | |||
|
|
| |||
Bottle continues to empty | • | Air is entering water bottle. | • | Check for leak in water bottle. | |
after complete filling. | |||||
|
|
|
| ||
|
|
| • Check orientation of bottle. | ||
| • Spring Valve Assembly damaged |
| Reposition so that fill valve on | ||
|
| bottom of bottle is depressed by | |||
Bottle not emptying. |
| or missing post in bottom of base. |
| post in bottom of base. | |
|
|
| The base will hold the contents of | ||
|
|
|
| ||
| • Base full of water. |
| water bottle (1.25 gallons). | ||
|
|
|
| Continue to run humidifier to | |
|
|
|
| deplete water from base. | |
Display blinks or fan |
|
|
|
| |
moves slightly when | • | Normal | • | No action required. | |
humidifier is plugged in. |
|
|
|
| |
Fan operating slower |
|
| • | Humidifier automatically switches | |
|
|
| fan to (LOW) F1 when “F” and | ||
than speed registered on | • | Humidifier in “DRY OUT MODE”. |
| ||
| alternating room humidity is | ||||
digital display |
|
|
| ||
|
|
| displayed. | ||
|
|
|
| ||
|
|
| • During “DRY OUT MODE” the | ||
Humidifier not shutting off |
|
|
| humidifier will continue to run on | |
• | Filter not dry. |
| “LOW” speed as required for up to |
Selecting a Location
Place humidifier on a flat level surface; take extra care in leveling when placing the unit on carpet. Position the humidifier where the most humidity is needed or where the most air will be circulated throughout the house such as near a cold air return.
Moist air (humidity) produced will disperse into the whole house, but the area closest to the unit will have the highest humidity. If the unit is positioned close to a window, condensation may form on the window pane. If this occurs the unit should be repositioned in another location.
during “DRY OUT MODE” |
| 2 hours or until the filter is | |
|
| ||
|
| completely dry. | |
Alternating “F” and room | • Reservoir is empty. | • Fill humidifier with water. | |
humidity displayed. | |||
|
| ||
Alternating “CF” and | • Filter may be dirty. | • Replace filter. | |
• Unplug unit for 30 seconds and | |||
room humidity displayed. | |||
| replug in to clear. | ||
|
|
4 | 13 |