TOOLS REQUIRED
Wire Cutters Pliers

SAFETY TIPS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS

1. Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-

2. 1999), including fire-rated construction.

3. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.

After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

4. one side of the outlet box and ungrounded conductor on the other side of the outlet box.

Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

5. to the service panel.

6. Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.

7. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from

8. the floor to the trailing edge of the blade.

WARNING – Risk of fire, electric shock, or personal injury, The fan in this box may be either directly supported from a structural framing mem- ber of a building and/or may be mounted to an outlet box marked acceptable for fan support of 31.8 kg. (70 lbs.) or less. Most outlet boxes commonly used for the support of luminaires may not be acceptable for fan support and may need to be replaced. Consult a qualified electrician

9. if in doubt.

10. Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.

11. Attach the mounting bracket using only the hardware supplied with the outlet box.

12. To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.

13. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.

14. NEVER place a switch where it can be reached from a tub or shower.

The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equip- ment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American

15. Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

 

Phillips Screwdriver

 

1

2

OUTLET BOX METHOD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning-Risk of

 

fire, electric shock, or person-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

al injury. The fan in this box may be either

 

 

 

 

 

 

directly supported from a structural framing

 

 

 

 

 

 

member of a building and/or may be mounted

 

 

Before you begin installing the fan, Switch power off

 

 

to an outlet box marked acceptable for fan sup-

 

 

at Service panel and lock service disconnecting means

 

 

port of of 31.8 kg (70 lbs) or less. Most outlet

 

 

to prevent power from being switched on accidentally.

 

 

boxes commonly used for the support of lummi-

 

 

When the service disconnecting means cannot be

 

 

naires may not be acceptable for fan support

 

 

locked, securely fasten a prominent warning device,

 

 

and may need to be replaced. Consult a quali-

 

 

such as a tag, to the service panel.

 

 

fied electrician if in doubt.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Step Ladder

3 BUILDING STRUCTURE METHOD

Outlet box

Wood Mounting

Screws Bracket

Secure mounting bracket directly to a joist from the buliding structure via the two knock out holes on the outlet box. Use only the appropri- ate wood screws and washers included with your fan. Caution: Wood screws must go through into the building joist.

4

5

6

Install canopy and yoke cover over the down- rod.

Thread wire through downrod with canopy and yoke cover assembled.

Insert downrod into motor yoke. Next, insert clevis pin through yoke and downrod and secure with cotter pin. (see inset)

Page 1 Page 3
Page 2
Image 2
Monte Carlo Fan Company 5MX Port of of 31.8 kg 70 lbs or less. Most outlet, Naires may not be acceptable for fan support
Page 1 Page 3

5MX specifications

The Monte Carlo Fan Company 5MX ceiling fan is a striking blend of modern design and advanced technology, making it a standout choice for both residential and commercial spaces. With sleek lines and a contemporary aesthetic, the 5MX ceiling fan complements various interior styles, from minimalist to industrial chic.

One of the key features of the 5MX is its powerful motor, designed for optimal airflow and energy efficiency. The fan operates smoothly at three distinct speed settings, providing tailored comfort for any environment. The whisper-quiet performance of the motor ensures that the fan circulates air without disruptive noise, making it ideal for bedrooms, living rooms, or office spaces.

The 5MX is equipped with a unique blade design that maximizes airflow while maintaining an elegant appearance. The fan blades are engineered to be aerodynamic, allowing for enhanced performance even at lower speeds. This results in a more efficient cooling experience without the typical high energy consumption associated with ceiling fans.

In addition to its aesthetic and performance features, the Monte Carlo 5MX ceiling fan incorporates innovative technology options. Many models come with integrated LED lighting, providing a functional and energy-efficient light source that can brighten any room. Some versions are also remote control-enabled, allowing for convenient operation from anywhere in the room.

The durability and quality of materials used in manufacturing the 5MX add to its appeal. The fan is built to withstand the test of time, with finishes that resist fading and corrosion, ensuring longevity and continued performance. The fan's installation process is straightforward, with clear instructions provided, making it accessible for both experienced installers and DIY enthusiasts.

Overall, the Monte Carlo Fan Company 5MX is designed to deliver unparalleled comfort while being energy efficient and stylish. Its modern features, technology, and elegant design make it an excellent addition to a variety of spaces, whether you seek to cool a cozy bedroom or enhance the ambiance of a large open area. With the 5MX, you can enjoy a perfect blend of functionality and fashion, making every environment more enjoyable. The ceiling fan not only elevates the overall aesthetic of a room but also contributes to a more comfortable living experience.
Top Page Image Contents