Features and
Functions Guide
H3
TURNING HEADSET
ON/OFF
To turn your headset on, press and hold the Call button until the indicator light flashes. Then, release the button.
WEARING THE
HEADSET
1Open the earhook.
2Loop the earhook over your ear.
CHANGING FOR USE
ON OTHER EAR
You can wear your H3 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear:
CHANGING VOLUME
BUTTON ORIENTATION
If you change your headset to wear on the other ear, you can also change the orientation of the volume buttons.
Bluetooth®
Handsfree Headset
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side of this guide
to complete initial setup of your H3.
To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off.
Call
Button
3Press the headset to your ear.
3
4
1Open the earhook 90 degrees from the headset.
2Gently lift and pull the top of the earhook up and off the upper hinge pin. Then, pull it away to remove it.
3Flip the headset over.
4Hook the bottom of the earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin.
1 Open Earhook
2 Pull Earhook Up
Hinge Pin
1Turn the headset power off.
2Press the Call button along with the Volume button you want to assign as "volume up" button until the indicator light flashes twice.
The headset power turns on.
Call
Button
Volume
Buttons
MAKING CALLS
Function | Action |
Make a voice dial call | Tap the Call button |
| and speak the |
| name after the tone |
End a call | Tap the Call button |
Receive a call | Tap the Call button |
Reject a call | Press and hold the |
| Call button until you |
| hear a beep |
Redial last call | Press and hold the |
| Call button until you |
| hear a beep |
Answer a second | Press and hold the |
incoming call | Call button (places |
| first call on hold) |
Note: Your H3 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information.
MAKING CALLS CONTINUED
Function | Action |
|
Toggle between two | Press and hold | |
active calls | the Call button | |
Join a | Press and hold | |
| both Volume buttons | |
Put an active call on | Press and hold the | |
hold or resume a call | Call button until you | |
on hold | hear a beep | |
Transfer a call from the | Tap the Call button | |
phone to the headset |
|
|
Disable or enable the | Press and hold | |
indicator light | both Volume | |
| buttons for 3 to 4 | |
| seconds | |
Mute or unmute a call | Tap both Volume | |
| buttons | |
Note: Some features are phone/network dependent.
INDICATOR LIGHTS
The indicator light provides information about your headset status.
With the Charger Plugged In
Headset Indicator | Headset Status |
On (steady) | Charging |
Off | Charging complete |
With No Charger Plugged In | |
|
|
Headset Indicator | Headset Status |
Off | Power off |
On (steady) | Pairing mode |
10 rapid flashes | Pairing successful |
Slow pulse | Connected |
| (on a call) |
Quick flash | Standby |
| (not on call) |
Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode.
AUDIO TONES
The audio tones provide information about your headset status.
Audio Tone | Headset Status |
|
Single high tone when | Volume at minimum | |
pressing volume button | or maximum | |
Five rapid high tones | Low battery | |
repeated every 60 sec. |
|
|
No audio indications; | Out of range | |
deteriorating quality |
|
|
Ring tone | Incoming call | |
Single high tone | Pairing confirmation | |
Single low tone | Voice activation | |
Dual high/low tone | Voice tag not | |
| recognized | |
Single high tone | End call | |
Low to high tone | Phone network | |
| not available | |
Two ascending tones | Mute enabled | |
Two descending tones | Mute disabled | |
