®
Two-Way Radio
User Guide
To maintain compliances with FCC RF exposure guidelines if you wear a radio on your body when transmitting always place the radio in a
If you do not use one of the
chemicals or particles (such as grain, dust or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in
Control Buttons
Radio Battery Meter |
|
| |
The radio battery icon shows the battery charge level, from full | to | ||
empty | . When the radio has one segment left, the |
| |
radio chirps periodically or after releasing | (Low Battery Alert). |
| |
Removing the NiMH Battery Pack
1. Turn the radio off. |
Setting the Volume
Press and hold 
for three seconds, then rotate 
until you reach a comfortable listening level.
1.Rotate 
clockwise to increase the volume.
2.Rotate 
counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.
INTERFERENCE ELIMINATOR TONE / CODE VALUES
CODE | (Hz) | CODE | (OCTAL) | CODE | (OCTAL) |
1 | 67.0 | 39 | 023 | 81 | 315 |
|
|
|
|
|
|
2 | 71.9 | 40 | 025 | 82 | 331 |
3 | 74.4 | 41 | 026 | 83 | 343 |
4 | 77.0 | 42 | 031 | 84 | 346 |
5 | 79.7 | 43 | 032 | 85 | 351 |
6 | 82.5 | 44 | 043 | 86 | 364 |
7 | 85.4 | 45 | 047 | 87 | 365 |
accessories and are not using the radio held in the normal use position, ensure the radio and its antenna are at least 1 inch ( 2.5 cm) from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without an accessory cable, position the radio and its antenna at least one inch
( 2.5 cm) from the body.
Approved Audio Accessories
•53724: Remote Speaker with
•53725: Headset with Swivel Boom Microphone
•53727: Earbud with
•53728: Flexible Ear Receiver
•56320: Earpiece with Boom Microphone
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
areas posted “Turn off
Operational Cautions
Antennas
Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
Batteries
All batteries can cause property damage and/or bodily injury such as burns if a conductive
Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries.
Battery Charger Safety Instructions:
Save these Instructions
Power
Switch / Volume
TX/RX LED
Indicator
Push to Talk (High)
Push to Talk (Low)
Call Tone
Flash Light
Button
Scroll
Charging Port
Emergency Alert
Bluetooth LED Indicator
Accessory Port
Scan / Monitor
Menu / Keypad Lock 
Scroll / Weather
Speaker
Microphone
Flash Light LED
2. | With the back of the radio facing you, make a 1/4 turn counter |
| clockwise to loosen the retaining screw on the battery door and |
| open the cover. |
3. | Remove the NiMH battery pack by pulling the ribbon attached to |
| the radio. |
4. | Close the battery cover and make a 1/4 turn clockwise to tighten the |
| retaining screw on the battery door. |
Removing the Three AA Alkaline Batteries (Optional Accessory)
1.Turn the radio off.
2.With the back of the radio facing you, make a 1/4 turn counter clockwise to loosen the retaining screw on the battery door and open the cover.
3.Gently remove each alkaline battery by easing each battery out individually.
4.Close the battery cover and make a 1/4 turn clockwise to tighten the retaining screw on the battery door.
Notes
• Exercise care when removing NiMH or AA batteries. Do not use |
Talking and Listening
To communicate, all radios in your group must be set to the same
(Hig
channel and Interference Eliminator Code.
1.To talk, press and hold 
.P (Low
2.When you are finished talking, release 
.
For maximum clarity, hold the radio two to three inches away from your mouth and speak directly into the microphone. Do not cover the microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve transmission range. Do not use the radios closer than five feet apart.
Power Boost
To boost your radio’s power up to high power, press the top portion of
(Hig
the 
button when talking. If you know your party is close by, you can
(Low
8 | 88.5 | 46 | 051 | 88 | 371 |
9 | 91.5 | 47 | 054 | 89 | 411 |
10 | 94.8 | 48 | 065 | 90 | 412 |
11 | 97.4 | 49 | 071 | 91 | 413 |
12 | 100.0 | 50 | 072 | 92 | 423 |
13 | 103.5 | 51 | 073 | 93 | 431 |
14 | 107.2 | 52 | 074 | 94 | 432 |
15 | 110.9 | 53 | 114 | 95 | 445 |
16 | 114.8 | 54 | 115 | 96 | 464 |
17 | 118.8 | 55 | 116 | 97 | 465 |
18 | 123.0 | 56 | 125 | 98 | 466 |
19 | 127.3 | 57 | 131 | 99 | 503 |
20 | 131.8 | 58 | 132 | 100 | 506 |
21 | 136.5 | 59 | 134 | 101 | 516 |
22 | 141.3 | 60 | 143 | 102 | 532 |
23 | 146.2 | 61 | 152 | 103 | 546 |
24 | 151.4 | 62 | 155 | 104 | 565 |
25 | 156.7 | 63 | 156 | 105 | 606 |
26 | 162.2 | 64 | 162 | 106 | 612 |
27 | 167.9 | 65 | 165 | 107 | 624 |
28 | 173.8 | 66 | 172 | 108 | 627 |
29 | 179.9 | 67 | 174 | 109 | 631 |
MU Series |
Motorola Talkabout
For More Information
For further information, you may call Motorola Solutions, Inc. at
Safety and General Information
Important Information on Safe and Efficient Operation
Read This Information Before Using Your Radio.
The information provided in this document supersedes the general safety information in user guides published prior to December 1, 2002.
Transmit and Receive Procedure
Your
•Transmit no more than 50% of the time.
•To receive calls, release the PTT button.
•To transmit (talk), press the Push to Talk (PTT) button.
Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance).
Exposure to Radio Frequency Energy
Your Motorola
•United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2
•American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95.
•Institute of Electrical and Electronics Engineers (IEEE) C95.
•International Commission on
•Health Canada - Safety Code 6; Limits of Human Exposure to Radiofrequency Electromagnetic Energy in the Frequency Range from 3 kHz to 300 GHz (2009).
•Australian Communications Authority Radiocommunications (Electromagnetic
•ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
•ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
To ensure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures.
Portable Radio Operation and EME Exposure
Antenna Care
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations.
conditions:
1.This device may not cause harmful interference; and
2.This device must accept any interference received, including interference that may cause undesired operation.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.
Aircraft
When instructed to do so, turn off your radio when onboard an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.
Medical Devices – Pacemakers
The Advanced Medical Technology Association recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with the independent research by and recommendations of the U.S. Food and Drug Administration.
People with pacemakers should:
•ALWAYS keep the radio more than 6 inches (15 cm) from their pacemaker when the radio is turned ON.
•Not carry the radio in the breast pocket.
•Use the ear opposite the pacemaker to minimize the potential for interference.
•Turn the radio OFF immediately if there is any reason to suspect that interference is taking place.
Medical Devices – Hearing Aids
Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.
Medical Devices – Other
If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.
Safety and General Use While Driving
Check the laws and regulations regarding the use of radios in the area where you drive, and always obey them. If you do use your radio while driving, please:
•Give full attention to driving and to the road.
•Use
•Pull off the road and park before making or answering a call if driving conditions so require.
The use of a
Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive atmosphere. Only radio types that are especially qualified should be used in such areas as “Intrinsically Safe.” Do not remove, install or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred to
1.Do not expose the charger to rain or snow.
2.Do not operate or disassemble the charger if it has received a sharp blow, or has been dropped or damaged in any way.
3.Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician. An improper condition can result in a risk of electric shock.
4.To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when disconnecting the charger from the AC receptacle.
5.To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.
6.Use of an attachment not recommended or sold by Motorola may result in a risk of fire, electric shock or personal injury.
7.Make sure the cord is located so it will not be stepped on, tripped over or subjected to damage or stress.
8.An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of a fire and/or electric shock. If an extension cord must be used, make sure that:
•The pins on the plug of the extension cord are the same number, size and shape as those on the plug of the charger.
•The extension cord is properly wired and in good condition.
•The extension cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to 150 feet.
9.The supply cord of the AC adaptor cannot be replaced. If the cord is damaged, call customer service at
FCC Licensing Information
Your Motorola radio operate s on General Mobile Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission (FCC). The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment. To obtain the FCC forms, please visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home to source form 605 and 159, which includes all the instructions you will need.
If you wish to have the document faxed or mailed, or if you have questions, please use the following contact information:
Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments
For a fax: | For mail service: | If you have |
Contact the | Call the FCC | questions about |
Forms Hotline | the FCC License: | |
system |
| Call the FCC |
|
|
|
|
| |
| (3676) |
|
should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.
Display Screen Guide
Numbers for Channel,
Call Tone
Numbers for Codes
Indicator | ||
(see menu Options) | ||
| Keypad Tone | |
Tone (Roger Beep) | ||
| ||
Without | ||
| ||
Accessories | ||
| ||
feature | ||
| ||
With Accessories | ||
|
Getting Started
Weatherproof
This radio is weatherproof to
The charging base and AC adaptor are not waterproof. Do not expose the charger to rain or snow. Charge the radios only in a dry location. Do not place wet radios into the charging base. The battery door must be tightly closed with the screw to maintain the weatherproof seal of the radio.
Installing the Batteries
Each radio can use either 1 NiMH rechargeable battery pack or 3 AA alkaline batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack
1.Turn the radio off.
2.With the back of the radio facing you, make a 1/4 turn to loosen the retaining screw on the battery door and open the cover.
3.Remove the NiMH battery pack from the clear plastic bag (do not disassemble or unwrap the battery pack).
4.Insert the NiMH battery pack with the diagram facing you. (The ribbon should be underneath the battery pack and should wrap around the right side of the pack for easy removal.)
5.Close the battery cover and tighten the retaining screw on the battery door.
Installing the Three AA Alkaline Batteries (Optional Accessory)
1. | Turn the radio off. |
2. | With the back of the radio facing you, make a 1/4 clockwise turn to |
| loosen the retaining screw on the battery door and open the cover. |
3. | Insert the three AA alkaline batteries with + and - polarity as shown |
| inside. (The ribbon should be underneath the AA alkaline batteries |
sharp or conductive tools to remove either of these batteries. |
• Remove the batteries before storing your radio for extended periods |
of time. Batteries corrode over time and may cause permanent |
damage to your radio. |
Using the mini-USB Charging Adaptor
The
Available
1.Vehicle charger
2.
If using a computer, the computer must be turned on.
This and other accessories (sold separately) are available for your radio. For more information, visit our Web site at motorolasolutions.com/talkabout or shop.giantintl.com.
1.Plug your
2.Plug the cable into the
3.After the initial charge, an empty battery will be fully charged in 14 hrs.
4.The battery icon will scroll as the battery is being charged. The scrolling icon will stop when the battery is fully charged.
Notes
•When moving between hot and cold temperatures, do not charge the NiMH battery pack until the battery temperature acclimates (usually about 20 minutes).
•If the radio is kept on while charging, the charging time will be extended.
•Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty | . Allow | |
time for the battery to charge to 1 bar | before attempting to | |
transmit a message. |
|
|
Attaching and Removing the Belt Clip
1.Attach belt clip to pocket or belt strap.
2.Align the belt clip post with the hole in the back of the radio.
3.Gently push until the clip clicks in place.
To Remove
1.Push down on the release tab at the top of the belt clip to release the catch.
2.Pull the belt clip away from the back of the radio.
Using the Desktop Battery Charger (Optional Accessory) (Model 1501)
The battery charger provides
1.Follow the steps above to install a NiMH Battery Pack.
2.Plug the AC power supply cord into the jack on the desk stand.
3.Plug the AC power supply into a standard wall outlet.
4.With a radio facing forward, slide it into one of the charging pockets.
5.When charging in the battery charger, the battery icon will scroll as the battery is being charged. The scrolling icon will stop when the battery is fully charged.
Turning your Radio On and Off
Turn 
clockwise to turn the radio on and counterclockwise to turn the radio off.
1. In the ON position, the radio chirps and briefly shows all feature |
icons available on the radio. |
conserve your battery’s energy by pushing the lower part of the 
P button to use less power.
Monitor Button
Pressing and holding 
for three seconds allows you to listen to the volume level of the radio when you are not receiving. This allows you to adjust the volume, if necessary. You can also press 
to check for activity on the current channel before you talk.
Push to Talk | Timeout Timer | (Hig |
To prevent accidental transmissions and save battery life, the radio emits a continuous warning tone and stops transmitting if you press 
forP 60 continuous seconds.
Menu Options
Selecting the Channel
Your radio has 22 channels. The channel is the frequency the radio uses to transmit. Channels
1.With the radio on, press 
. The current channel will flash.
2.Press 
or 
and select an unused or quiet channel.
3.Press 
to save the channel setting or 
to continue set up.
Note: When the radio is on a 0.5 watt channel, 
displays. When the radio is on a 1.5 watts channel, 
displays.
FRS / GMRS SIMPLEX CHANNELS AND FREQUENCIES
Channel | FREQ. (MHz) | TYPE | Channel | FREQ. (MHz) | TYPE |
|
|
|
|
|
|
1 | 462.5625 | GMRS/FRS | 12 | 467.6625 | FRS |
|
|
|
|
|
|
2 | 462.5875 | GMRS/FRS | 13 | 467.6875 | FRS |
|
|
|
|
|
|
3 | 462.6125 | GMRS/FRS | 14 | 467.7125 | FRS |
|
|
|
|
|
|
4 | 462.6375 | GMRS/FRS | 15 | 462.5500 | GMRS |
|
|
|
|
|
|
5 | 462.6625 | GMRS/FRS | 16 | 462.5750 | GMRS |
|
|
|
|
|
|
6 | 462.6875 | GMRS/FRS | 17 | 462.6000 | GMRS |
|
|
|
|
|
|
7 | 462.7125 | GMRS/FRS | 18 | 462.6250 | GMRS |
|
|
|
|
|
|
8 | 467.5625 | FRS | 19 | 462.6500 | GMRS |
|
|
|
|
|
|
9 | 467.5875 | FRS | 20 | 462.6750 | GMRS |
|
|
|
|
|
|
10 | 467.6125 | FRS | 21 | 462.7000 | GMRS |
|
|
|
|
|
|
11 | 467.6375 | FRS | 22 | 462.7250 | GMRS |
|
|
|
|
|
|
Selecting the Interference Eliminator Code
Interference Eliminator Codes help minimize interference by blocking transmissions from unknown sources. Your radio has 121 Interference Eliminator Codes. Codes 1 – 38 are the standard analog codes that appear on other FRS/GMRS radios. Codes 39 – 121 are additional digital codes added for superior interference protection. 0 is the off position, no analog or digital codes are enabled.
1. Press 
until the code starts to flash.
(Hig
2.Press 
or to select the code.
3.Press 
toP save the code setting or to 
continue set up.
(Low
You can set a different code for each channel using this procedure. An extended press 
or 
allows you to scroll through the Interference Code rapidly so you can quickly reach the code you want.
Note: You must set the Interference Eliminator Code to 0 to communicate with radios that do not have Interference Eliminator Codes.
30 | 186.2 | 68 | 205 | 110 | 632 |
31 | 192.8 | 69 | 223 | 111 | 654 |
32 | 203.5 | 70 | 226 | 112 | 662 |
33 | 210.7 | 71 | 243 | 113 | 664 |
34 | 218.1 | 72 | 244 | 114 | 703 |
35 | 225.7 | 73 | 245 | 115 | 712 |
36 | 233.6 | 74 | 251 | 116 | 723 |
37 | 241.8 | 75 | 261 | 117 | 731 |
38 | 250.3 | 76 | 263 | 118 | 732 |
|
| 77 | 265 | 119 | 734 |
|
| 78 | 271 | 120 | 743 |
|
| 79 | 306 | 121 | 754 |
|
| 80 | 311 |
|
|
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group so you can alert them that you want to talk. Your radio has 20 call tones from which to choose.
To set a call tone:
1.Press 
three times until the current call tone setting flashes and 
appears.
2.Press 
or 
to change and hear the call tone.
3.Press 
to set the new call tone or 
to continue set up.
To transmit your call tone to other radios set to the same channel and Interference Eliminator Code as your radio, press 
.
Note: Setting the call to 0 disables the call tone feature.
Hands-Free Use Without Accessories ( 
)
You can use the iVOX feature to transmit
1.Press 
until 
2.Press 
or 
to select On or Off.
3.Press 
to set or 
to continue set up.
Hands-Free Use With Accessories ( 
—)
You can transmit
Many accessories (sold separately) are available for your radio. For more information, visit our Web site at motorolasolutions.com/talkabout or shop.giantintl.com.
1.Turn the radio off and plug the VOX accessory into the accessory port.
2.Turn the radio on. VOX shows on the display.
3.Adjust the volume appropriately by rotating 
. Lower the volume before placing the accessory on your head or in your ear.
4.To turn off, simply remove accessory.
Note: There is a short delay between the time you start talking and when the radio transmits. There is a short delay before the transmission is completed.
Setting the Sensitivity Level When in 
—Mode
Adjusting the radio’s sensitivity level helps minimize the possibility of unintended noises triggering a transmission and helps the radio pick up soft voices.
1.Press 
until VOX and the level setting (1 - 3) appear on the display.
2.Press 
or 
to select the sensitivity level.
3.Press 
to set or 
to continue set up.
Do NOT hold the antenna when the radio is “IN USE.” Holding the antenna affects its effective range.
above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains
and should wrap around the right side of the batteries.) |
4. Close the battery cover and tighten the retaining screw on the |
battery door. |
2. The display screen then shows the current channel, code and all |
features that are enabled. |
Continued on back
