9.The supply cord of the AC adaptor cannot be replaced. If the cord is damaged, call customer service at
Control Buttons
Volume
|
| Emergency Alert | |
| LED Indicator | ||
(High) |
|
| |
| Accessory Jack | ||
(Low) |
| ||
|
| ||
Microphone |
| Flashlight Button | |
|
| ||
|
| Scan/Monitor | |
Call Tone |
|
| |
|
| Menu/Lock | |
Scroll/Weather |
|
| |
| Flashlight LED | ||
R350 Radio line drawing | |||
Charging Port |
|
| |
Display Screen Guide | |||
Numbers for Channel, |
| ||
Call Tone |
| R | |
|
| ||
Numbers for Codes |
| ||
— Battery Meter | — Scan | ||
— Channel Power | — Vibrate | ||
Indicator | — Call Tone, | ||
(see Menu Options) | |||
— Lock |
| Keypad Tone | |
| — Weather Alert | ||
— Talk Confirmation | |||
— | |||
Tone (Roger Beep) | |||
— Noise Filtering | Use Without | ||
Accessories | |||
R — Repeater Channel | — | ||
— On/Off for each | Use With | ||
Accessories | |||
feature |
|
FCC Licensing Information
Your Motorola radio operate son General Mobile Radio Service (GMRS) frequencies and is subject to the Rules and Regulations of the Federal Communications Commission (FCC). The FCC requires that all operators using GMRS frequencies obtain a radio license before operating their equipment. To obtain the FCC forms, please visit the FCC’s Web site at wireless.fcc.gov/uls/index.htm?job=home to source form 605 and 159, which includes all the instructions you will need.
If you wish to have the document faxed or mailed, or if you have questions, please use the following contact information:
For a fax: | For mail service: | If you have |
Contact the | Call the FCC | questions about |
Forms Hotline | the FCC License: | |
system |
| Call the FCC |
|
|
|
|
| |
| (3676) |
|
Changes or modifications not expressly approved by Motorola may void the user’s authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules.
Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.
Getting Started
Installing the Batteries
Each radio can use either 1 NiMH rechargeable battery pack or 3 AA alkaline batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack (Optional Accessory)
1.Turn the radio off.
2.With the back of the radio facing you, lift the battery cover latch up and remove the cover.
3.Remove the NiMH battery pack from the clear plastic bag (do not disassemble or unwrap the battery pack).
4.Insert the NiMH battery pack with the diagram facing you. (The ribbon should be underneath the battery pack and should wrap around the right side of the pack for easy removal.)
5.Reposition the battery cover and press down to secure.
Installing the Three AA Alkaline Batteries
1.Turn the radio off.
2.With the back of the radio facing you, lift the battery cover latch up and remove the cover.
3.Insert the three AA alkaline batteries with + and - polarity as shown inside. (The ribbon should be underneath the AA alkaline batteries and should wrap around the right side of the batteries.)
4.Reposition the battery cover and press down to secure.
Radio Battery Meter
The radio battery icon shows the battery charge level, from full
to empty | . When the radio has one segment left, the | |
radio chirps periodically or after releasing | (Low Battery | |
Alert). |
|
|
Removing the NiMH Battery Pack (Optional Accessory)
1.Turn the radio off.
2.With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover.
3.Remove the NiMH battery pack by pulling the ribbon attached to the radio.
4.Reposition the battery cover and press down to secure.
Removing the Three AA Alkaline Batteries
1.Turn the radio off.
2.With the back of the radio facing you, lift the battery latch up to release the battery cover and remove the cover.
3.Gently remove each alkaline battery by easing each battery out individually.
4.Reposition the battery cover and press down to secure.
Notes
•Exercise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries.
•Remove the batteries before storing your radio for extended periods of time. Batteries corrode over time and may cause permanent damage to your radio.
Using the Battery Charger (Optional Accessory)
The battery charger provides
1.Follow the steps above to install a NiMH Battery Pack.
2.Plug the AC power supply cord into the jack on the desk stand.
3.Plug the AC power supply into a standard wall outlet.
4.With a radio facing forward, slide it into one of the charging pockets.
5.When charging in the battery charger, the red light on the charger base will glow continuously.
Using the mini-USB Charging Connector
The
Available mini-USB charging options (Optional Accessories):
1.Wall travel charger
2.Vehicle charger
3.
If using a computer, the computer must be turned on.
This and other accessories (sold separately) are available for your radio. For more information, visit our Web site at www.motorola.com or shop.giantintl.com.
1.Plug your
2.Plug the cable into the
3.An empty battery will be fully charged in 14 hours.
4.The LED indicator light on the radio will glow to indicate that the battery is charging.
Notes
•The light will remain red after the NiMH battery pack is fully charged.
•When moving between hot and cold temperatures, do not charge the NiMH battery pack until the battery temperature acclimates (usually about 20 minutes).
•For optimal battery life, remove the radio from the charger within 16 hours. Do not store the radio while connected to the charger.
•If the radio is kept on while charging, the charging time will be extended.
•Even though the charger is connected, you may not be
able to transmit a message if the battery is completely empty
. Allow time for the battery to charge to 1 bar before attempting to transmit a message.
Attaching and Removing the Belt Clip
1.Attach belt clip to pocket or belt strap.
2.Align the belt clip post with the hole in the back of the radio.
3.Gently push until the clip clicks in place.
To Remove
1.Push down on the release tab at the top of the belt clip to release the catch.
2.Pull the belt clip away from the back of the radio.
Turning your Radio On and Off
Turn clockwise to turn the radio on and counterclockwise to turn the radio off.
1.In the ON position, the radio chirps and briefly shows all feature icons available on the radio.
2.The display screen then shows the current channel, code and all features that are enabled.
Setting the Volume |
|
|
Press and hold | for three seconds while rotating | until you |
reach a comfortable listening level. |
|
1.Rotate clockwise to increase the volume.
2.Rotate counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the same channel and Interference Eliminator Code.
1. To talk, press and hold .
2 | MR355/MR356 |
|