GENERAL INFORMATION

A.Your MR. HEATER portable gas-fired infra-red heater comes fully assembled and is tested at the factory for proper gas and input as stated on the nameplate.

B.Each heater is equipped with a 100% safety shutoff, push button valve which will automatically stop the flow of gas in the event the heater fails to operate for any reason. A tip over switch and an excess flow check are also standard on the model MH35LPTS.

C.Before proceeding with this installation, be sure to inspect for damages. The freight company must be notified of any damages and request that an inspection be made. MR. HEATER will send replacements for damaged parts only after receiving a signed inspection report to prove the liability of the freight company.

FOR SAFE OPERATION

A.READ THESE INSTRUCTIONS CAREFULLY. Read and adhere to these instructions. DO NOT allow anyone who has not read these instructions to assemble, light, adjust or operate this heater.

B.LP-Gas IS HIGHLY FLAMMABLE. In the event of a leak, LP- Gas will accumulate and the possibility of a fire is present. LP-Gas is scented and its strong odor is readily detectable. Never strike a match, bring any flame or create an electric spark in an enclosure when you smell LP-Gas. Ventilate the area thoroughly, move the heater outside, and correct the source of the leak before attempting to light any appliance.

C.Always operate the heater with the LP-Gas cylinder in an upright position on a level non-combustible surface. NEVER

PLACE THE CYLINDER ON ITS SIDE WHEN OPERATING THE HEATER.

D.DO NOT attempt to operate the heater with any gas other than that indicated on the heater nameplate.

INSTALLATION INSTRUCTIONS

GENERAL

For the U.S. and/or Canada, the installation of this appliance must comply with local and/or Provincial codes or, in the absence of these codes,

With the (U.S.) National Fuel Gas Code, ANSI Z223.1 – Latest Edition, AND with the (U.S.) Standard for the Storage and Handling of Liquified Petroleum Gases, ANSI/NFPA 58, OR

With the current (Canadian) CAN/CGA B149.1 AND B149.2 INSTALLATION CODES.

This heater (including hose and regulator assembly) must be inspected before each use and at least annually by a qualified service person. If the hose for Model MH35LPTS shows evidence of excessive abrasion or wear, or if the hose is cut, it must be replaced prior to the heater being put into operation. The replacement hose assembly shall be that specified by the manufacturer. See the parts list.

The minimum ambient temperature rating for this heater is 20 degrees F.

This heater incorporates a “Tip Over” switch which automatically shuts off the burner in the event of tipping. Ensure that this switch is in the vertical position and is secured with the screws provided (see Fig. 4). DO NOT operate this heater with the

LP-gas supply cylinder in any other than the upright position.

LOCATION

Although this heater incorporates a “tip over” switch, the heater and LP-Gas supply cylinder must be located on a hard, flat, level surface to minimize the risk of accidental tipping. The LP Gas supply cylinder should be adequately restrained to prevent accidental tipping. DO NOT OPERATE this heater with the supply cylinder in any other than the upright position.

This appliance must be installed only in locations where the potential for physical damage to the appliance (i.e., due to physical contact) is reduced to a minimum.

The installer must inform the owner/operator of this appliance that precautions must be taken to protect the appliance from physical damage.

This appliance produces radiant heat. Therefore, it must be located at least six feet away from any LP-Gas container and must not be directed toward any LP-Gas container within 20 feet.

The heater must be installed in a location such that it will not be exposed directly to water spray, rain, and/or dripping water.

Use of this heater in a draft/windy area may decrease its efficiency. If possible, operate the unit in a draft free area or turn the face of the heater away from the draft.

PIPING:

For Model MH35LPTS (for use with LP-Gas)

This model may be connected to a self-contained LP-Gas supply system using the hose and regulator assembly supplied with the appliance, OR, it may be connected to a permanently installed LP-Gas supply system.

If connected to a self-contained LP-Gas supply system, the hose assembly must be inspected prior to each use of the heater. If it is evident that there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the heater being put into operation.

If connected to a self-contained LP-Gas supply system, the cylinder must have no less than a minimum capacity of 20 pounds and no more than a maximum capacity of 100 pounds of LP-Gas. DO NOT connect this appliance to a cylinder having less than a nominal 20 pound capacity of LP-Gas. DO NOT connect this appliance to more than one (1) 100 pound cylinder.

WARNING

NEVER USE A FORK LIFT TRUCK TYPE CYLINDER.

Mr. Heater Gas-Fired Infra-Red Portable Construction Heater

3

Operating Instructions and Owner’s Manual

Page 3
Image 3
Mr. Heater MH35LPTS owner manual General Information, For Safe Operation, Installation Instructions

MH35LPTS specifications

The Mr. Heater MH35LPTS is a powerful and versatile portable propane heater designed for both indoor and outdoor use. It is particularly favored by those who require a reliable heating source in various settings, including garages, workshops, camping sites, and during emergencies. With its blend of functionality and ease of use, the MH35LPTS has become a popular choice among consumers looking for efficient heating solutions.

One of the key features of the MH35LPTS is its impressive heating capacity, producing up to 35,000 BTUs per hour. This makes it capable of warming spaces of up to 800 square feet, ensuring that users can maintain a comfortable environment even in colder conditions. Operating on a standard 20 lb. propane tank, the heater is not only efficient but also cost-effective, as propane tends to be a more affordable fuel option compared to electric heating systems.

The Mr. Heater MH35LPTS incorporates advanced safety features, including an automatic low oxygen shut-off system (ODS) and a tip-over safety shut-off valve. These safety mechanisms ensure that the heater will turn off automatically if oxygen levels drop too low or if the unit is accidentally knocked over, providing peace of mind for users, especially when using the heater indoors.

Another significant characteristic of the MH35LPTS is its ease of portability. With a lightweight design and a built-in carry handle, the heater can be easily moved from one location to another, making it ideal for various applications. Whether you need warmth for a construction site or comfort during a camping trip, this heater can be transported with minimal effort.

The heater also features an adjustable heat setting, allowing users to customize the temperature according to their preferences. The straightforward control mechanism ensures that even those who are not familiar with heating equipment can easily operate it.

In summary, the Mr. Heater MH35LPTS is an excellent choice for anyone in need of a reliable and efficient heating solution. With its robust heating capacity, essential safety features, portable design, and user-friendly controls, this propane heater effectively meets the demands of both indoor and outdoor use. Whether for work or leisure, the MH35LPTS stands out as a dependable option for generating warmth when it is needed the most.