5.If adjustment is necessary, loosen the jam nut on the traction drive cable, and thread cable in or out as necessary.

6.Tighten the jam nut to secure the cable when correct adjustment is reached. Reassemble the frame cover with six self-tapping screws.

Friction

Wheel

Gear

Shaft

Drive

Plate

Figure 26

Note: If you had earlier placed plastic film under the gas cap, be sure to remove it once the adjustment to the traction drive clutch is done and the snow thrower frame is re-installed.

ADJUSTING AUGER CLUTCH

To adjust the auger clutch, refer to the Final Adjustments in section 5.

ADJUSTING SHIFT ROD

1.Remove the hairpin clip and flat washer from the ferrule and remove the ferrule from the shift lever. Place the shift lever in the fastest forward speed position.

Models 642, 662:

2.Push up on the shift arm assembly as far as it will go. Thread the ferrule up or down the shift rod and align with the lower hole on the wider side of the shift lever assembly behind the handle panel. Secure the ferrule to the shift arm assembly again with the hardware earlier removed.

Models 614, 644, 664, and 6A4:

3.Push down on the shift arm assembly as far as it will go. Thread the ferrule up or down the shift rod and align it with the hole closest to the shift knob on the narrow side of the shift lever assembly behind the handle panel.

NOTE: Make certain to check for correct adjustment of the shift rod as instructed in the Final Adjustments section before operating the snow thrower.

CARBURETOR ADJUSTMENT

WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of heated surfaces and muffler.

Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude and load.

Refer to the separate engine manual packed with your unit for carburetor adjustment information.

DRIVE WHEELS

The wheels may be adjusted for two different methods of operation. The adjustment is made by placing the klick pins in one of two different holes on the right side of the unit. See Figure 27.

1.One Wheel Driving—Place klick pin in the outside axle hole on the right side. This position gives power drive to the left wheel only, making the unit easier to maneuver.

2.Both Wheels Driving—Place klick pin in the hole in the hub next to the rim on the right side. This position is good for heavy snow as there is power drive in both wheels.

Klick Pin in Hole

in Hub Next to Rim

Outside Hole

in Axle

Figure 27

15

Page 14 Page 16
Page 15
Image 15
MTD E664F, E6A4E, E662H, E644E, E642E manual Adjusting Auger Clutch, Adjusting Shift ROD, Carburetor Adjustment, Drive Wheels
Page 14 Page 16

E642E, E644E, E662H, E6A4E, E664F specifications

The MTD E664F, E6A4E, E642E, E644E, and E662H are innovative models within the MTD lineup, showcasing cutting-edge features and advanced technologies designed to provide optimal performance and versatility for various applications.

The MTD E664F stands out with its robust build and powerful engine, making it a reliable choice for commercial and heavy-duty tasks. It incorporates a user-friendly control system, enhancing the operator experience and ensuring precise handling. Its high-capacity fuel tank allows for longer work intervals, reducing downtime and increasing productivity.

Meanwhile, the MTD E6A4E model is tailored for efficiency and ease of use. This unit features a compact design, making it ideal for urban environments or smaller workspaces. Its lightweight construction facilitates effortless maneuverability, while the advanced cutting technology ensures a clean and even finish. Users will appreciate the minimal maintenance requirements, further adding to its appeal.

The MTD E642E combines power with versatility. Equipped with a range of adaptable attachments, this model is suitable for multiple applications, from landscaping to snow removal. Its durable chassis and high-torque engine deliver superior performance under varying conditions. Additionally, the model’s ergonomic design ensures operator comfort during extended use, making it a favorite among professionals.

Similar to the E642E, the MTD E644E focuses on flexibility but enhances it with smart technology integration. Featuring an intuitive interface and connectivity options, operators can monitor and manage operations remotely. This connectivity maximizes uptime through predictive maintenance alerts and efficiency tracking.

Lastly, the MTD E662H is a high-performance model that is engineered for heavy-duty applications. Its powerful engine is paired with advanced transmission technology, ensuring smooth operation even under the most demanding conditions. The fully adjustable settings allow operators to customize performance to meet specific requirements, while the rugged construction promises longevity and reliability.

These models collectively embody MTD’s commitment to innovation and quality, offering various features, including durability, adaptability, and user-focused design. Whether for professional landscaping, agriculture, or maintenance tasks, the MTD E664F, E6A4E, E642E, E644E, and E662H provide a comprehensive range of solutions tailored to meet the needs of today’s operators, reinforcing MTD’s reputation in the market.
Top Page Image Contents