SECTION 4: CONTENTS OF HARDWARE PACK

Lay out the hardware according to the illustration for identification purposes. Part numbers are shown in parentheses. (Hardware pack may contain extra items which are not used on your unit.)

A ATTACHING THE HANDLES

C ATTACHING THE CHUTE ASSEMBLY

AND CLUTCH GRIPS

 

 

 

 

 

Hex Bolts

 

 

 

 

 

5/16-18 x 1-3/4”

Hex Bolts

 

 

 

 

(710-3180)

 

 

 

 

5/16-18 x 3/4”

 

 

 

 

 

(710-3008)

 

 

 

Saddles

 

 

 

 

Hex Bolts

(784-5599)

 

 

 

 

 

 

(710-3015)

 

Lock Washers

 

 

1/4-20 x 3/4”

 

 

 

 

 

5/16” I.D.

 

 

 

 

(736-0119)

 

 

 

Carriage Bolts

 

 

 

 

5/16-18 x 1-1/2”

 

Chute Flange

 

(710-0262)

 

 

Keepers

Hex Lock Nuts

 

 

 

(731-0851A)

1/4”-20

 

 

 

 

 

(712-3027)

 

 

Cupped Washers

 

 

 

 

 

5/16” I.D.

D ATTACHING THE CHUTE CRANK

 

 

(736-0242)

Hex Nuts

 

Spacers

 

 

Flat Washers

 

 

 

3/8” I.D. x 5/8” O.D.

5/16”-18

 

(750-1032)

 

 

(736-0185)

(712-3010)

 

 

Hex Nut

 

 

 

 

 

 

Hex Bolts

Hex Lock Nuts

5/16”-18

Hair Pin Clip

 

(712-3010)

 

5/16-18 x 2”

(714-0104)

 

5/16”-18

 

 

 

(710-3103)

(712-0429)

 

 

Cupped Washers

 

 

 

 

5/16” I.D.

 

 

 

 

 

 

 

 

 

 

(736-0242)

ATTACHING THE SHIFT ROD

 

 

 

B AND CONTROL CABLES

 

E AUGER SHEAR BOLTS (SPARES)

 

 

 

 

 

 

 

 

Shear Bolts

 

 

 

 

 

(710-0890A)

 

Flat Washers

 

 

 

Hex Lock Nuts

Ferrule

Hair Pin Clip

 

 

5/16”-18

3/8” I.D. x 5/8” O.D.

 

 

(712-0429)

(711-0677)

 

 

(736-0275)

(714-0104)

 

 

 

 

 

 

 

 

 

 

F

ATTACHING THE TRACK CONTROLS

 

 

“Z”-Fitting

 

Track

 

 

 

(746-0778)

 

 

 

Jam Nuts

 

Controls

 

 

#10-24 Thread

 

(746-0950)

 

 

(712-0121)

 

 

 

 

NOTE: The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. If you hit a hard foreign object or an ice jam, the snow thrower is designed so that the bolts may shear. Two replacement shear bolts and nuts are provided for your convenience. Store in a safe place until needed.

IMPORTANT: NEVER replace the auger shear bolts with standard hex bolts. Any damage to the auger gearbox or other components as a result of doing so will NOT be covered by your snow thrower’s warranty.

5

Page 5
Image 5
MTD E762F manual Contents of Hardware Pack