Maintaining Your Snow Thrower, Skid Shoe

Skid Shoe

The space between the shave plate and the ground can be adjusted by raising or lowering the skid shoes.

For close snow removal, as when using on a smooth concrete or asphalt driveway, place the skid shoes in the low position. Use the middle or high position when the area to be cleared is uneven. When operating on gravel, always put skid shoes in the high position. See Figure 15.

Adjust skid shoes as follows:

•Loosen, but do not remove, the hex flange locknuts which fasten the skid shoe to the auger housing.

•Raise or lower the skid shoe to desired position.

•Retighten the hex nuts loosened earlier.

NOTE: Make certain the bottom surface of skid shoe is flat against the ground to avoid uneven wear .

Shave Plate

Skid

Shoes

High

Low

Hex Flange Locknuts

•Repeat on the other side of the snow thrower.

Figure 15

SECTION 6: MAINTAINING YOUR SNOW THROWER

WARNING: Before lubricating, repairing, or inspecting, disengage all clutch levers and stop engine. Wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

Gear Shaft

•Lubricate the gear shaft with 6-in-1 grease (part number 737-0170) at least once a season, or after every 25 hours of operation. Refer to Figure 14.

IMPORTANT: Keep all grease and oil off the rubber friction wheel and drive plate.

General Recommendations

•Always observe safety rules when performing any maintenance.

•The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain the snow thrower as instructed in this manual.

•Some adjustments will have to be made periodically to maintain your unit properly.

•Periodically check all fasteners and hardware to make sure these are tight.

Engine

Refer to the engine manual for instructions.

Gear Case

The gear case is lubricated with grease at the factory and it does not require checking.

•If disassembled for any reason, lubricate with 2 ounces of Shell Alvania grease EPR00, part number 737-0168. Before reassembling, remove old sealant and apply new sealant.

IMPORTANT: Do not overfill the gear case, since damage to the seals could result. Be sure the vent plug is free of grease in order to relieve pressure.

Lubrication

Drive and Shifting Mechanism

•At least once a season or after every 25 hours of operation, remove rear cover. Lubricate any chains, sprockets, gears, bearings, shafts, and the shifting mechanism at least once a season. Use engine oil or a spray lubricant. Refer to Figure 14.

IMPORTANT: Avoid spillage of oil on rubber friction wheel and aluminum drive plate.

Auger Shaft

•At least once a season, remove the shear pins from the auger shaft and spray lubricant inside the shaft. See Figure 16.

OGST-3106 specifications

The MTD OGST-3106 is an innovative and versatile outdoor gas-powered string trimmer designed to meet the demands of both professional landscapers and passionate gardeners. This robust machine combines power, efficiency, and ease of use, making it a top choice for managing grass, weeds, and other vegetation.

One of the standout features of the MTD OGST-3106 is its powerful 31cc 2-cycle engine. This engine is engineered to deliver exceptional performance, allowing users to tackle thick underbrush and heavy grass with ease. The engine is designed for optimal fuel efficiency, reducing the need for frequent refueling during larger jobs. In addition to power, the lightweight design of the trimmer ensures that users can maneuver it effortlessly, reducing fatigue even during prolonged use.

The MTD OGST-3106 incorporates a straight shaft design, which provides extended reach for accessing hard-to-reach areas such as under decks or along fences. This feature enhances its versatility, making it suitable for a variety of applications, from trimming along sidewalks to edging flower beds. Moreover, the unit is equipped with a dual-line cutting head that allows for increased cutting width and efficiency, ensuring a cleaner and faster job.

Another key characteristic of the MTD OGST-3106 is its easy-start technology. The trimmer features user-friendly starting mechanisms that make it simple to get the engine running, even for those who may not have extensive experience with gas-powered equipment. This eliminates some of the common hassles associated with starting similar machines, making it accessible to users of all skill levels.

Durability is a hallmark of the MTD OGST-3106, constructed with high-quality materials that withstand the rigors of outdoor use. Its robust build ensures longevity and reliability over time, even when facing tough environmental conditions. The trimmer also includes ergonomic grips that enhance comfort and control, enabling users to work efficiently while minimizing strain on their hands and wrists.

In conclusion, the MTD OGST-3106 is a powerful and user-friendly gas string trimmer that combines advanced technology with practical features. It is ideal for anyone looking to maintain their outdoor space effectively. Whether you are a professional landscaper or a DIY enthusiast, the MTD OGST-3106 is designed to help you achieve professional-quality results with ease and efficiency. Its blend of power, durability, and ergonomic design sets it apart in the competitive market of outdoor power equipment.

MTD OGST-3106 Maintaining Your Snow Thrower, Skid Shoe, General Recommendations, Lubrication

Models: OGST-3106