SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks,

GEARSHIFT LEVER

NEUTRAL LOCK GATE

flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

22

FIG. 23

Page 21 Page 23
Page 22
Image 22
Murray 96017000500 Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig, To Start Engine with a Weak Battery See Fig
Page 21 Page 23

96017000500 specifications

Murray 96017000500 represents a cutting-edge technological solution in the realm of industrial generators, designed to cater to diverse power requirements across various sectors. This generator is engineered for reliability, efficiency, and versatility, making it an ideal choice for businesses that necessitate uninterrupted power supply.

One of the standout features of the Murray 96017000500 is its robust power output. With a capacity that easily meets the demands of both small and medium-sized enterprises, this generator ensures that operations can continue smoothly, even during electrical outages. The design is focused on delivering a steady 120/240V output, accommodating a range of equipment and tools.

The generator incorporates advanced engineering that prioritizes fuel efficiency. It operates on a gas-fueled engine which not only enhances performance but also reduces emissions compared to traditional diesel generators. This aspect aligns with the growing global emphasis on sustainable and environmentally friendly practices in business operations.

Durability is another hallmark of the Murray 96017000500. Built with high-quality materials and superior craftsmanship, it is designed to withstand harsh operational conditions. This resilience ensures that the generator can function consistently over extended periods, minimizing downtime and maintenance costs for businesses.

Ease of use is an essential characteristic of this generator. It features an intuitive control panel that allows operators to monitor performance and make adjustments with minimal effort. Quick-connect ports facilitate straightforward setup and integration into existing power systems, making it accessible even for those with limited technical expertise.

Safety features are integrated throughout the design, with overload protection and automatic shut-off mechanisms in place to prevent damage during power surges. These safety measures underscore Murray's commitment to providing products that are not only high-performing but also secure for users.

In terms of portability, the Murray 96017000500 is designed with mobility in mind. Its compact dimensions and lightweight construction allow for easy transportation and installation at various job sites, making it a practical choice for contractors and tradespeople on the move.

In summary, the Murray 96017000500 is a powerful, efficient, and durable generator that meets the demanding needs of contemporary businesses. With its advanced fuel system, user-friendly interface, and built-in safety features, it represents an ideal investment for those looking to ensure a reliable power supply in any situation.
Top Page Image Contents