NAD C545BEE owner manual Reference, Using the C 545BEE CD 8 Remote Control, Troubleshooting

OPERATION

USING THE C 545BEE – CD 8 REMOTE CONTROL

ENGLISH

FRANÇAIS

A wireless remote control is provided with your compact disc player, enabling you to operate playback functions from the comfort of your chair or from virtually anywhere in the room. For reliable operation there should be a clear line-of-sight path from the remote control to the front of the CD player. If the player does not respond to remote commands, it may be that this line-of-sight path is obstructed by clothing, paper or furnishings.

Most of the buttons on the remote control handset have the same effect as the corresponding buttons on the front panel of the player. In addition, the handset is equipped with some extra buttons like the following function keys.

NUMERIC KEY PAD

Using the direct-entry numeric keypad (0 to 9) causes the C 545BEE to jump directly to the beginning of a numbered track and commence play. Thus, to play Track 5, simply press “5”. To play Track 20, press “2” and “0”.

DIMMER

Toggle to reduce, turn off and restore VFD brightness.

PROGRAM AND DELETE

Use [PROG] button to start, review, edit or exit programming mode. In combination with [PROG] button, the [CLEAR] button allows the deletion of a programmed track during program review or edit sequence. Refer also to the item about “PROGRAMMING” at the “USING THE C 545BEE – FEATURES” section of the “OPERATION” page.

FILTER

The [FILTER] button is used for selecting the bandwidth of the audio low pass filter for the CD, MP3 and WMA media being played. The options are NORMAL Bandwidth and SLOW Bandwidth. For some recordings the SLOW Bandwidth may provide a wide frequency range and spatial feeling. Toggle

CD 8's [FILTER] button to select “NORMAL” or “SLOW” mode. “NORMAL FILTER” or “SLOW FILTER” will be correspondingly shown in the VFD.

ESPAÑOL

ITALIANO

DEUTSCH NEDERLANDS SVENSKA

РУССКИЙ

RPT A-B		NORMAL: Select NORMAL bandwidth to engage a standard CD high-
To repeat a sequence, implement the following procedures:
		pass filter slope for playback of CD, MP3, and WMA music through the
1	Press [RPT A-B] at your chosen starting point.
		two channel stereo audio jacks.
2	Press [RPT A-B] again at your chosen end point. The repeat sequence
		SLOW: Select SLOW bandwidth to engage a gentle high-pass filter
	begins.
		slope for playback of CD music through the two channel stereo audio
3	Press [RPT A-B] again to cancel the sequence.
		jacks. This feature is particularly useful for higher bit rate recordings.

REFERENCE

TROUBLESHOOTING

CONDITION		POSSIBLE CAUSES		POSSIBLE SOLUTIONS
No power.	•	The power cord is disconnected.	•	Plug the power cord into the wall outlet
				securely.
The power is ON, but the C 545BEE does	•	No disc is inserted.	•	Insert a disc.
not work.
The C 545BEE does not start playback.	•	The disc is loaded upside down.	•	Reload the disc with the label side UP.
	• The disc is too dirty.		•	Clean the disc.
No sound.	• The equipment connected with the audio		• Select the correct input mode of the audio
		cable is not set to receive CD signal output.		receiver so you can listen to the sound from
				the C 545BEE.
	• The power of the equipment connected with		• Turn on the equipment connected with the
		the audio cable is turned off.		audio cable.
Sound skips.	•	The C 545BEE is subject to vibration or physical	•	Change the installation location.
		shock from external sources.
The remote control does not work properly.	•	The remote control is not pointed at the	•	Point the remote control at the remote
		remote sensor on the CD player.		sensor of the CD player.
	•	The remote control is too far from the CD	•	Operate the remote control closer to the
		player.		CD player.
	•	The remote control batteries are dead.	•	Replace the remote control batteries.

12