![REAR PANEL](/images/new-backgrounds/12423/124239x1.webp)
CONTROLS AND CONNECTIONS
10
|
|
|
| XLR |
|
| CAUTION |
|
|
|
| BALANCE |
|
| RISK OF ELECTRIC SHOCK |
|
|
|
| PIN 1 GND |
|
| DO NOT OPEN |
|
|
|
|
|
|
| |
115V/60Hz |
|
|
| PIN 2 HI |
|
| ATTENTION: SHOCK HAZARD - DO NOT OPEN |
|
|
| PIN 3 LO |
|
| RISQUE DE CHOC ELECTRIQUE NE PAS QUVRIR. | |
230V/50Hz |
|
|
|
|
|
|
|
|
|
|
|
|
|
| NADY SYSTEMS, Inc. |
AC IN |
|
|
|
|
|
| Emeryville, CA, USA |
|
|
|
|
|
| Made in China | |
FUSE 0.5A/250V HIGH | MID | LOW |
| HIGH | MID | LOW | |
|
| ||||||
| R CHANNEL | OUTPUTS | INPUT | SUB WOOFER | L CHANNEL | OUTPUTS | INPUT |
14 | 15 | 11 | 12 | 13 | 11 | 12 |
|
| |||||
|
|
|
|
|
REAR PANEL
10. POWER CONNECTOR
The IEC jack is used to connect the power cord to the AC Power Source.
(Caution: Do not remove the center grounding pin.)
11.L/M/H OUTPUT CONNECTORS:
Connect to your amplifiers via these balanced XLR output jacks.
12.BALANCED INPUT CONNECTORS (Combo 1/4” TRS & XLR):
Connect your L/R stereo input signal to these balanced combo jacks. These combination 1/4” TRS (Tip/Ring/Sleeve) phone jacks and XLR jacks are compatible with either type balanced connector and are wired as Tip/Pin 3 = (+), Ring/Pin 2 =
13.SUBWOOFER OUTPUT CONNECTOR:
Connect to your subwoofer amplifier via this balanced XLR output jack.
14.AC VOLTAGE SELECTOR SWITCH:
Before plugging in the power cord, check to see that the unit is set for the proper voltage for your area: ~115V (60Hz) or ~230V (50Hz).
15.FUSE COMPARTMENT :
Replace with only the same type fuse (0.5A/250V). If it blows continuously, do not use the unit until it has been serv- iced by qualified personnel.
| SPECIFICATIONS |
Crossover Type | Stereo 3 ways + Subwoofer |
Crossover Frequencies Subwoofer | 50 - 250Hz |
LM | 70 – 1000Hz |
MH | 480 – 7000Hz |
Filter Type (Slope) | 2nd order, 12dB/Octave |
Inputs Type | Balanced Combo 1/4” TRS & XLR |
Impedance | 100K Ω |
Outputs Type | Balanced XLR |
Impedance | 220 Ω |
Low Cut Filters | 30Hz/ - 3dB, 12dB/Octave |
Frequency Response | 25Hz - 25KHz |
Total Harmonic Distortion (THD) + Noise | < 0.05 % |
S/N Ratio | > 80 dB |
Fuse | 0.5 A/ 250V, 5x20mm glass type |
Dimensions | 19’’ x 1.73’’ x 5.9’’ (483 X 44 X 150mm) |
Weight | 4.4 lbs. (2.2 Kg) |
Specifications and design subject to change without prior notice for improvement purposes
5