Nady Systems TMP-3 owner manual Specifications, Legal Information, Using The Side Chain, License

and the RATIO (13) control low (fully counterclockwise). This is a very low compression setting. To increase the amount of compression, lower the THRESHOLD (12) control and increase the RATIO (13) control until the desired amount is achieved.

Connects to tip SEND

Connects to ring RETURN

USING THE SIDE CHAIN (19)

To use the SIDE CHAIN (19) to directly access the compressor circuitry you'll need an insert cable like the one shown above. The Tip-Ring-Sleeve stereo end plugs into the TMP-3 SIDE CHAIN lack. The 1/4" SEND plug connects to the Input of a signal

processor such as an equalizer, the 1/4" RETURN plug connects to the signal processor Output. The signal in the SIDE CHAIN is not heard on the Output of the TMP-3, it only effects the action of the compressor. The higher the level of signal in the SIDE CHAIN, the more compression will occur.

EQUALIZER SETTINGS (7,8,9,10)

Begin with all controls set at 0 or center detente position. This is the equivalent of a "bypass". Adjusting the LEVEL (15) controls will increase or decrease the amount of the indicated frequency range. The MID SWEEP (9) control adjusts the actual frequency that the MID LEVEL (8) control will adjust.

USING THE PROCESSES TOGETHER

Increasing the Mic Preamp GAIN settings to the point where slight distortion occurs will effect the overall frequency content of the output signal. EQ adjustments may need to be made. Experiment with different settings until you've achieved the desired sound.

SPECIFICATIONS

Input Impedance:	600 Ω	balanced,
	50K Ω TRS unbalanced (1/4”)
Output Impedance:	50K Ω TRS balanced (1/4”)
Max Input Level:	-15dBV XLR 600Ω , +18dBV (1/4”)
Max Gain:		+65dB
Max Output Level:		+22dB
Frequency Response:	20Hz-25KHz +/-3dB
Total Harmonic Distortion (THD) + Noise:		0.1%
Noise Floor:		-75dB
Equalizer Boost/Cut:		+/-15dB

Equalizer Settings:	LOW SHELF: 150Hz
	HIGH SHELF: 10KH
	MID FREQUENCIES: 300Hz-5KHz, Q=1
Compressor Settings:	THRESHOLD: -30dB to +20dB;
	RATIO: 2:1 to 8:1
Indicators:	PHANTOM POWER, CLIP, POWER,
	ANALOG VU METER
Input/Output Jacks:	XLR balanced, 1/4” unbalanced,
	1/4” TRS unbal. Side Chain
Dimensions:	19" x 1.75" x 6" (483 x 44 x 162mm)
Weight:	3.5 lbs.( 1.75 Kg)

The specifications above are correct at the time of printing of this manual. For improvement purposes, all specifications for this unit, including design and appearance, are subject to change without prior notice.

LEGAL INFORMATION

NOTICE

The information in this document is subject to change, as the Company may make changes to product in order to improve reliability, design, or function, without prior written notice. No part of this manual may be reproduced or transmitted in any form or by any means without the written permission of the company.

IN NO EVENT WILL THE COMPANY BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING DIRECTLY OR INDIRECTLY, SUCH AS LOSS OF PROFIT OR GOOD WILL, THAT MAY BE SUFFERED IN CONNECTION WITH THE PURCHASE OF THIS PRODUCT OR FROM THE BREACH OF ANY REPRESENTATION OR WARRANTY.

LICENSE

The Company grants the customer a non-exclusive, non-transferable license to use the software, if any, accompanying this product for internal use on a single computer system. The end user may make a single copy of the software solely for backup purposes; otherwise, no copies may be made of the software or any part thereof. No other license of any kind is granted to any part of the product or any of the intellectual property therein.

7